Quantcast
Channel: Recent Discussions - Repetier-Forum
Viewing all 9285 articles
Browse latest View live
↧

G2 arc command doesnot seem to follow feedrate commands

April 25, 2020, 4:38 am
$
0
0
Hi,

I am building my own delta printer. I use a MKS GEN L v1 board with repetier firmware v1.0.

For controlling, I use Repetier server 0.93.1 installed on a raspberry pi 3b+ (with repetier image).  I have been using the repetier server with my pursa i3 for a while now and it is working good (Great job on all of these. Thank you that). Both pursa and my delta are never on at the same time. So the server is connected to only one printer at any given point.

I have a been testing my delta in cnc mode to see how it works. I am only doing dry runs as of now (no tool is connected to the mks board). All works fine when my gcode does not have G2 commands. When I use G2 commands to create arcs, one the following happens:
  1. Sometimes the arcs moves as expected - no issues.
  2. Sometimes the arcs movements speed up (even though I have the same F defined for all the lines of Gcode), but the delta is able to handle this faster movements.
  3. Sometimes the arcs movements speed up a lot and the stepper motor seems to skip steps.
All three cases can happen in the same job for different arcs and it seems to happen randomly. My printer logs don't should anything unusual (to my knowledge, attached below).

It only happens when there are G2 commands in the gcode. I did run the job after removing the G2 commands manually and it works fine. I havn't run anything with G3 command yet. I am not sure if I am doing something wrong or what is causing the issue. Any help in this case would be highly appreciated.

Below is the gcode I am using, it was generated using Freecad Path Workbench and then modified manually.

Please let me know if you need any additional information. Thank you in advance.

--------------------------------GCODE-----------------------------------------

G28
G0 F900.000
G1 F900.000
M453
G1 Z28
G92 X0 Y0 Z10
G1 Z15
G1 X41.8713 Y39.1046 Z6.0000
G1 X49.0513 Y34.9593 Z6.0000
G2 X54.8013 Y25.0000 Z6.0000 I-5.7500 J-9.9593 F900.000
G1 X54.8013 Y-25.0000 Z6.0000
G2 X49.0513 Y-34.9593 Z6.0000 I-11.5000 J-0.0000 F900.000
G1 X5.7500 Y-59.9593 Z6.0000
G2 X1.5796 Y-61.3910 Z6.0000 I-5.7500 J9.9593 F900.000
G2 X-5.7500 Y-59.9593 Z6.0000 I-1.5796 J11.3910 F900.000
G1 X-49.0513 Y-34.9593 Z6.0000
G2 X-54.8013 Y-25.0000 Z6.0000 I5.7500 J9.9593 F900.000
G1 X-54.8013 Y25.0000 Z6.0000
G2 X-49.0513 Y34.9593 Z6.0000 I11.5000 J0.0000 F900.000
G1 X-5.7500 Y59.9593 Z6.0000
G2 X5.7500 Y59.9593 Z6.0000 I5.7500 J-9.9593 F900.000
G1 X41.8713 Y39.1046 Z6.0000
G1 X41.8713 Y39.1046 Z2.0000
G1 X49.0513 Y34.9593 Z2.0000
G2 X54.8013 Y25.0000 Z2.0000 I-5.7500 J-9.9593 F900.000
G1 X54.8013 Y-25.0000 Z2.0000
G2 X49.0513 Y-34.9593 Z2.0000 I-11.5000 J-0.0000 F900.000
G1 X5.7500 Y-59.9593 Z2.0000
G2 X1.5796 Y-61.3910 Z2.0000 I-5.7500 J9.9593 F900.000
G2 X-5.7500 Y-59.9593 Z2.0000 I-1.5796 J11.3910 F900.000
G1 X-49.0513 Y-34.9593 Z2.0000
G2 X-54.8013 Y-25.0000 Z2.0000 I5.7500 J9.9593 F900.000
G1 X-54.8013 Y25.0000 Z2.0000
G2 X-49.0513 Y34.9593 Z2.0000 I11.5000 J0.0000 F900.000
G1 X-5.7500 Y59.9593 Z2.0000
G2 X5.7500 Y59.9593 Z2.0000 I5.7500 J-9.9593 F900.000
G1 X41.8713 Y39.1046 Z2.0000
G1 X41.8713 Y39.1046 Z0.0000
G1 X49.0513 Y34.9593 Z0.0000
G2 X54.8013 Y25.0000 Z0.0000 I-5.7500 J-9.9593 F900.000
G1 X54.8013 Y-25.0000 Z0.0000
G2 X49.0513 Y-34.9593 Z0.0000 I-11.5000 J-0.0000 F900.000
G1 X5.7500 Y-59.9593 Z0.0000
G2 X1.5796 Y-61.3910 Z0.0000 I-5.7500 J9.9593 F900.000
G2 X-5.7500 Y-59.9593 Z0.0000 I-1.5796 J11.3910 F900.000
G1 X-49.0513 Y-34.9593 Z0.0000
G2 X-54.8013 Y-25.0000 Z0.0000 I5.7500 J9.9593 F900.000
G1 X-54.8013 Y25.0000 Z0.0000
G2 X-49.0513 Y34.9593 Z0.0000 I11.5000 J0.0000 F900.000
G1 X-5.7500 Y59.9593 Z0.0000
G2 X5.7500 Y59.9593 Z0.0000 I5.7500 J-9.9593 F900.000
G1 X41.8713 Y39.1046 Z0.0000
G1 Z15

----------------------------End of Gcode--------------------------------------------
------------------------------Print Log---------------------------------------------

11:30:10.849: N473 G28
11:30:10.853: ok 473
11:30:10.853: N474 G0 F900.000
11:30:12.721: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:12.854: busy:processing
11:30:13.820: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:30:14.854: busy:processing
11:30:14.918: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:30:14.922: SelectExtruder:0
11:30:14.928: FlowMultiply:100
11:30:14.930: X:0.00 Y:0.00 Z:115.000 E:0.0000
11:30:14.930: ok 474
11:30:14.930: N475 G1 F900.000
11:30:14.935: ok 475
11:30:14.935: N476 M453
11:30:14.940: ok 476
11:30:14.940: N477 G1 Z28
11:30:15.118: PrinterMode:CNC
11:30:15.118: ok 477
11:30:15.118: N478 G92 X0 Y0 Z10
11:30:15.124: ok 478
11:30:15.124: N479 G1 Z15
11:30:15.127: X_OFFSET:0.000 Y_OFFSET:0.000 Z_OFFSET:-18.000
11:30:15.127: ok 479
11:30:15.127: N480 G1 X41.8713 Y39.1046 Z6.0000
11:30:15.133: ok 480
11:30:15.133: N481 G1 X49.0513 Y34.9593 Z6.0000
11:30:15.235: ok 481
11:30:15.235: N482 G2 X54.8013 Y25.0000 Z6.0000 I-5.7500 J-9.9593 F900.000
11:30:15.251: ok 482
11:30:15.251: N483 G1 X54.8013 Y-25.0000 Z6.0000
11:30:23.703: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (8)
11:30:24.527: ok 483
11:30:24.527: N484 G2 X49.0513 Y-34.9593 Z6.0000 I-11.5000 J-0.0000 F900.000
11:30:25.900: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:26.136: ok 484
11:30:26.136: N485 G1 X5.7500 Y-59.9593 Z6.0000
11:30:28.096: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:28.529: ok 485
11:30:28.529: N486 G2 X1.5796 Y-61.3910 Z6.0000 I-5.7500 J9.9593 F900.000
11:30:29.194: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:30:30.121: ok 486
11:30:30.121: N487 G2 X-5.7500 Y-59.9593 Z6.0000 I-1.5796 J11.3910 F900.000
11:30:30.134: ok 487
11:30:30.134: N488 G1 X-49.0513 Y-34.9593 Z6.0000
11:30:31.390: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:31.775: ok 488
11:30:31.775: N489 G2 X-54.8013 Y-25.0000 Z6.0000 I5.7500 J9.9593 F900.000
11:30:33.586: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:33.803: ok 489
11:30:33.804: N490 G1 X-54.8013 Y25.0000 Z6.0000
11:30:35.782: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:36.118: ok 490
11:30:36.119: N491 G2 X-49.0513 Y34.9593 Z6.0000 I11.5000 J0.0000 F900.000
11:30:36.881: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:30:37.859: ok 491
11:30:37.859: N492 G1 X-5.7500 Y59.9593 Z6.0000
11:30:40.176: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (3)
11:30:40.256: ok 492
11:30:40.256: N493 G2 X5.7500 Y59.9593 Z6.0000 I5.7500 J-9.9593 F900.000
11:30:41.274: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:30:41.998: ok 493
11:30:41.998: N494 G1 X41.8713 Y39.1046 Z6.0000
11:30:43.470: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:44.395: ok 494
11:30:44.395: N495 G1 X41.8713 Y39.1046 Z2.0000
11:30:45.666: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:45.968: ok 495
11:30:45.969: N496 G1 X49.0513 Y34.9593 Z2.0000
11:30:45.975: ok 496
11:30:45.975: N497 G2 X54.8013 Y25.0000 Z2.0000 I-5.7500 J-9.9593 F900.000
11:30:45.990: ok 497
11:30:45.990: N498 G1 X54.8013 Y-25.0000 Z2.0000
11:30:47.862: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:48.442: ok 498
11:30:48.442: N499 G2 X49.0513 Y-34.9593 Z2.0000 I-11.5000 J-0.0000 F900.000
11:30:48.961: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:30:49.934: ok 499
11:30:49.934: N500 G1 X5.7500 Y-59.9593 Z2.0000
11:30:52.156: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (3)
11:30:52.248: ok 500
11:30:52.249: N501 G2 X1.5796 Y-61.3910 Z2.0000 I-5.7500 J9.9593 F900.000
11:30:53.257: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:30:53.991: ok 501
11:30:53.991: N502 G2 X-5.7500 Y-59.9593 Z2.0000 I-1.5796 J11.3910 F900.000
11:30:54.254: ok 502
11:30:54.255: N503 G1 X-49.0513 Y-34.9593 Z2.0000
11:30:55.450: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:56.053: ok 503
11:30:56.054: N504 G2 X-54.8013 Y-25.0000 Z2.0000 I5.7500 J9.9593 F900.000
11:30:57.646: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:30:58.094: ok 504
11:30:58.094: N505 G1 X-54.8013 Y25.0000 Z2.0000
11:30:59.842: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:00.524: ok 505
11:31:00.524: N506 G2 X-49.0513 Y34.9593 Z2.0000 I11.5000 J0.0000 F900.000
11:31:02.104: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:02.105: ok 506
11:31:02.105: N507 G1 X-5.7500 Y59.9593 Z2.0000
11:31:03.137: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:31:04.097: ok 507
11:31:04.097: N508 G2 X5.7500 Y59.9593 Z2.0000 I5.7500 J-9.9593 F900.000
11:31:05.333: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:05.823: ok 508
11:31:05.823: N509 G1 X41.8713 Y39.1046 Z2.0000
11:31:07.530: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:08.107: ok 509
11:31:08.107: N510 G1 X41.8713 Y39.1046 Z0.0000
11:31:09.726: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:09.781: ok 510
11:31:09.781: N511 G1 X49.0513 Y34.9593 Z0.0000
11:31:09.841: ok 511
11:31:09.841: N512 G2 X54.8013 Y25.0000 Z0.0000 I-5.7500 J-9.9593 F900.000
11:31:09.981: ok 512
11:31:09.981: N513 G1 X54.8013 Y-25.0000 Z0.0000
11:31:11.922: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:12.719: ok 513
11:31:12.719: N514 G2 X49.0513 Y-34.9593 Z0.0000 I-11.5000 J-0.0000 F900.000
11:31:14.126: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:14.126: ok 514
11:31:14.126: N515 G1 X5.7500 Y-59.9593 Z0.0000
11:31:16.316: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:16.536: ok 515
11:31:16.536: N516 G2 X1.5796 Y-61.3910 Z0.0000 I-5.7500 J9.9593 F900.000
11:31:17.414: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:31:18.262: ok 516
11:31:18.262: N517 G2 X-5.7500 Y-59.9593 Z0.0000 I-1.5796 J11.3910 F900.000
11:31:18.511: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:31:18.526: ok 517
11:31:18.526: N518 G1 X-49.0513 Y-34.9593 Z0.0000
11:31:19.616: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:31:20.326: ok 518
11:31:20.326: N519 G2 X-54.8013 Y-25.0000 Z0.0000 I5.7500 J9.9593 F900.000
11:31:21.806: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:22.367: ok 519
11:31:22.367: N520 G1 X-54.8013 Y25.0000 Z0.0000
11:31:24.002: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:24.798: ok 520
11:31:24.799: N521 G2 X-49.0513 Y34.9593 Z0.0000 I11.5000 J0.0000 F900.000
11:31:26.206: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:26.540: ok 521
11:31:26.540: N522 G1 X-5.7500 Y59.9593 Z0.0000
11:31:28.395: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:28.936: ok 522
11:31:28.936: N523 G2 X5.7500 Y59.9593 Z0.0000 I5.7500 J-9.9593 F900.000
11:31:30.591: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:30.677: ok 523
11:31:30.677: N524 G1 X41.8713 Y39.1046 Z0.0000
11:31:32.789: T:-48.82 /0 B:-48.82 /0 B@:0 @:0 (2)
11:31:33.075: ok 524
11:31:33.075: N525 G1 Z15
11:31:33.886: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:31:34.748: ok 525
11:31:35.077: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:31:35.077: @stopLog
11:31:35.749: wait
11:31:36.082: T:-48.82 /0 B:-48.82 /0 B@:0 @:0
11:31:36.749: wait

--------------------End of Log-------------------------------------------------------


↧
Search

WLAN Probleme, immer wieder Aussetzer

April 26, 2020, 1:03 am
$
0
0
Hallo liebes Repetier-Forum,

ich hoffe ich bekomme hier auch auf Deutsch geholfen, ich glaube mein englisch ist für so technische Details nicht so super! :)

Ich habe seit gestern einen Raspberry Pi 4 mit 2GB, original RPi 5,1V 3A Netzteil und original RPi 7 Zoll Touchdisplay. Aufgesetzt mit der aktuellen Repetier-Server-Version und auch soweit funktionsfähig eingerichtet habe ich ständig Aussetzer im WLAN, hab dann mal ein Ping dauerhaft laufen lassen und sehe immer wieder das sporadisch kein Ping durchgeht.

WLAN geht über Fritzbox 7590 womit ich allgemein sonst keine Probleme habe.

Habe den Repetier-AP schon deaktiviert und das WLAN über die XML-Datei eingerichtet.

Hat da schon jemand Erfahrungen oder Lösungen für mich?

Danke im voraus!
↧
↧

Filament Runout not pushing message to Repetier-Informer

April 26, 2020, 12:09 am
$
0
0
Hi,
I am using Repetier Server Pro 0.93.1 on a Raspberry Pi 3B+ and my printer uses an SKRv1.4 controller with Marlin 2.0.5.3 firmware.
The log below contains the line:
> 16:27:41.690: echo:Insert filament and send M108
I have added this to /usr/local/Repetier-Server/firmware/repetier.xml as:
<response type="outOfFilament">^echo:Insert filament and send M108</response>
And various variations including:
<response type="outOfFilament">Insert filament</response>
And rebooted the server each time, however whenever the firmware detects a jam, the message is not pushed to Repetier-Informer (all other messages work in Repetier-Informer, and all message types are turned on in Repetier-Server).

Is there something else I am misssing?

See the following print log extract when the firmware detects a filament runout:
< 16:26:12.482: N15 M73 P0 R76 Q0 S76
> 16:26:13.982: ok N15 P63 B31
> 16:26:13.982:  T:200.36 /200.00 B:60.05 /60.00 @:25 B@:22
> 16:26:13.983:  T:200.18 /200.00 B:60.05 /60.00 @:62 B@:0
< 16:26:13.983: N16 G90                       ; Use absolute coordinates
< 16:26:13.983: N17 M82                       ; Set E codes absolute (default)
< 16:26:13.983: N18 M107                      ; RepRap Fan off
> 16:26:13.984: Slow command added:G28                       ; Home all axis
< 16:26:13.984: N19 G28                       ; Home all axis
< 16:26:13.984: N20 G1 Z0.16
< 16:26:13.984: N21 G92 Z0 E0                 ; Reset Z and Extruder
< 16:26:13.984: ;@execute pi_temp
< 16:26:13.987: ;@execute enclosure
< 16:26:13.989: N22 M140 S60
> 16:26:14.028: ok N16 P63 B31
> 16:26:14.029: ok N17 P63 B26
> 16:26:14.029: ok N18 P63 B27
< 16:26:14.029: N23 M105
> 16:26:14.029: Slow command added:M190 S60
< 16:26:14.029: N24 M190 S60
> 16:26:14.571:  T:200.18 /200.00 B:60.00 /60.00 @:29 B@:3
> 16:26:15.572:  T:200.00 /200.00 B:59.90 /60.00 @:67 B@:40
> 16:26:16.029: echo:busy: processing
> 16:26:16.572:  T:200.18 /200.00 B:59.90 /60.00 @:32 B@:10
> 16:26:17.572:  T:200.18 /200.00 B:59.84 /60.00 @:54 B@:24
> 16:26:18.029: echo:busy: processing
> 16:26:18.571:  T:200.36 /200.00 B:59.84 /60.00 @:4 B@:11
> 16:26:19.571:  T:200.18 /200.00 B:59.79 /60.00 @:50 B@:31
> 16:26:20.030: echo:busy: processing
> 16:26:20.574:  T:200.54 /200.00 B:59.74 /60.00 @:0 B@:37
> 16:26:21.574:  T:200.18 /200.00 B:59.69 /60.00 @:43 B@:50
> 16:26:22.030: echo:busy: processing
> 16:26:22.575:  T:200.36 /200.00 B:59.69 /60.00 @:23 B@:54
> 16:26:23.574:  T:200.36 /200.00 B:59.69 /60.00 @:26 B@:45
> 16:26:24.030: echo:busy: processing
> 16:26:24.573:  T:200.36 /200.00 B:59.69 /60.00 @:22 B@:48
> 16:26:25.573:  T:200.18 /200.00 B:59.74 /60.00 @:61 B@:33
> 16:26:25.922: X:0.00 Y:0.00 Z:0.32 E:0.00 Count X:0 Y:0 Z:128
> 16:26:25.922: ok N19 P63 B26
> 16:26:25.922: ok N20 P62 B27
> 16:26:25.922: X:0.00 Y:0.00 Z:0.00 E:0.00 Count X:0 Y:0 Z:128
> 16:26:25.922: ok N21 P62 B28
> 16:26:25.922: ok N22 P62 B29
< 16:26:25.922: M117 ETA 17:34:45 day 26
< 16:26:25.923: N25 M104 S200
< 16:26:25.923: N26 M105
> 16:26:25.923: Slow command added:M109 S200
< 16:26:25.923: N27 M109 S200
> 16:26:25.927: ok T:200.36 /200.00 B:59.69 /60.00 @:0 B@:63
< 16:26:25.927: N28 M82 ;absolute extrusion mode
> 16:26:25.931:  T:200.36 /200.00 B:59.69 /60.00 @:0 B@:63 W:?
> 16:26:26.574:  T:200.18 /200.00 B:59.69 /60.00 @:24 B@:67
> 16:26:26.932:  T:200.18 /200.00 B:59.69 /60.00 @:27 B@:60 W:19
> 16:26:27.574:  T:200.00 /200.00 B:59.74 /60.00 @:33 B@:44
> 16:26:27.926: echo:busy: processing
> 16:26:27.931:  T:200.00 /200.00 B:59.74 /60.00 @:43 B@:68 W:18
> 16:26:28.574:  T:200.00 /200.00 B:59.74 /60.00 @:47 B@:58
> 16:26:28.931:  T:200.00 /200.00 B:59.79 /60.00 @:62 B@:51 W:17
> 16:26:29.574:  T:200.00 /200.00 B:59.79 /60.00 @:32 B@:53
> 16:26:29.931:  T:200.00 /200.00 B:59.79 /60.00 @:30 B@:51 W:16
> 16:26:29.932: echo:busy: processing
> 16:26:30.573:  T:200.00 /200.00 B:59.79 /60.00 @:30 B@:66
> 16:26:30.931:  T:200.00 /200.00 B:59.84 /60.00 @:30 B@:48 W:15
> 16:26:31.573:  T:200.00 /200.00 B:59.84 /60.00 @:20 B@:51
> 16:26:31.932:  T:200.00 /200.00 B:59.90 /60.00 @:28 B@:43 W:14
> 16:26:31.932: echo:busy: processing
> 16:26:32.574:  T:199.87 /200.00 B:59.84 /60.00 @:60 B@:56
> 16:26:32.933:  T:199.87 /200.00 B:59.90 /60.00 @:36 B@:29 W:13
> 16:26:33.575:  T:199.87 /200.00 B:59.90 /60.00 @:39 B@:71
> 16:26:33.932:  T:200.00 /200.00 B:59.90 /60.00 @:11 B@:60 W:12
> 16:26:33.932: echo:busy: processing
> 16:26:34.574:  T:199.87 /200.00 B:59.95 /60.00 @:33 B@:41
> 16:26:34.932:  T:199.87 /200.00 B:59.95 /60.00 @:31 B@:43 W:11
> 16:26:35.574:  T:200.00 /200.00 B:60.00 /60.00 @:15 B@:37
> 16:26:35.932:  T:199.87 /200.00 B:60.00 /60.00 @:46 B@:41 W:10
> 16:26:35.932: echo:busy: processing
> 16:26:36.584:  T:199.87 /200.00 B:60.00 /60.00 @:43 B@:45
> 16:26:36.933:  T:200.00 /200.00 B:59.95 /60.00 @:22 B@:67 W:9
> 16:26:37.583:  T:200.00 /200.00 B:60.05 /60.00 @:27 B@:54
> 16:26:37.932:  T:200.00 /200.00 B:60.05 /60.00 @:30 B@:45 W:8
> 16:26:37.932: echo:busy: processing
> 16:26:38.584:  T:199.87 /200.00 B:60.09 /60.00 @:52 B@:15
> 16:26:38.932:  T:199.87 /200.00 B:60.09 /60.00 @:35 B@:30 W:7
> 16:26:39.584:  T:200.00 /200.00 B:60.05 /60.00 @:37 B@:48
> 16:26:39.932:  T:200.00 /200.00 B:60.09 /60.00 @:31 B@:32 W:6
> 16:26:39.932: echo:busy: processing
> 16:26:40.583:  T:200.00 /200.00 B:60.09 /60.00 @:25 B@:37
> 16:26:40.931:  T:199.87 /200.00 B:60.09 /60.00 @:47 B@:37 W:5
> 16:26:41.582:  T:200.00 /200.00 B:60.09 /60.00 @:25 B@:36
> 16:26:41.931:  T:200.00 /200.00 B:60.14 /60.00 @:14 B@:20 W:4
> 16:26:41.931: echo:busy: processing
> 16:26:42.583:  T:199.87 /200.00 B:60.19 /60.00 @:37 B@:8
> 16:26:42.931:  T:200.00 /200.00 B:60.14 /60.00 @:26 B@:40 W:3
> 16:26:43.582:  T:199.87 /200.00 B:60.14 /60.00 @:53 B@:30
> 16:26:43.945: echo:busy: processing
> 16:26:43.949:  T:200.00 /200.00 B:60.14 /60.00 @:13 B@:42 W:1
> 16:26:44.583:  T:199.87 /200.00 B:60.19 /60.00 @:34 B@:7
> 16:26:44.949:  T:199.87 /200.00 B:60.14 /60.00 @:32 B@:38 W:0
> 16:26:45.582:  T:199.87 /200.00 B:60.19 /60.00 @:32 B@:16
> 16:26:45.928: ok N24 P63 B26
> 16:26:45.928: ok P63 B27
> 16:26:45.928: ok N25 P63 B28
< 16:26:45.928: M117 ETE 01:06:10
< 16:26:45.928: N29 G92 E0
< 16:26:45.928: N30 G92 E0
> 16:26:45.932: ok T:200.00 /200.00 B:60.19 /60.00 @:22 B@:21
< 16:26:45.932: N31 G1 F3000 E-0.75
> 16:26:45.937:  T:200.00 /200.00 B:60.19 /60.00 @:23 B@:21 W:?
> 16:26:46.584:  T:200.00 /200.00 B:60.19 /60.00 @:19 B@:18
> 16:26:46.936:  T:200.00 /200.00 B:60.19 /60.00 @:22 B@:27 W:19
> 16:26:47.583:  T:199.87 /200.00 B:60.14 /60.00 @:39 B@:45
> 16:26:47.936:  T:199.87 /200.00 B:60.19 /60.00 @:33 B@:17 W:18
> 16:26:47.936: echo:busy: processing
> 16:26:48.583:  T:199.87 /200.00 B:60.19 /60.00 @:51 B@:9
> 16:26:48.936:  T:200.00 /200.00 B:60.19 /60.00 @:19 B@:23 W:17
> 16:26:49.583:  T:199.87 /200.00 B:60.19 /60.00 @:55 B@:14
> 16:26:49.935:  T:199.87 /200.00 B:60.19 /60.00 @:36 B@:12 W:16
> 16:26:49.935: echo:busy: processing
> 16:26:50.583:  T:199.87 /200.00 B:60.19 /60.00 @:45 B@:11
> 16:26:50.936:  T:200.00 /200.00 B:60.19 /60.00 @:27 B@:3 W:15
> 16:26:51.583:  T:199.87 /200.00 B:60.09 /60.00 @:41 B@:45
> 16:26:51.936:  T:199.87 /200.00 B:60.14 /60.00 @:34 B@:13 W:14
> 16:26:51.936: echo:busy: processing
> 16:26:52.595:  T:200.00 /200.00 B:60.14 /60.00 @:28 B@:24
> 16:26:52.936:  T:199.87 /200.00 B:60.14 /60.00 @:39 B@:4 W:13
> 16:26:53.595:  T:199.87 /200.00 B:60.14 /60.00 @:47 B@:4
> 16:26:53.936:  T:199.87 /200.00 B:60.14 /60.00 @:39 B@:1 W:12
> 16:26:53.936: echo:busy: processing
> 16:26:54.595:  T:199.87 /200.00 B:60.09 /60.00 @:50 B@:25
> 16:26:54.936:  T:200.00 /200.00 B:60.14 /60.00 @:25 B@:0 W:11
> 16:26:55.595:  T:200.18 /200.00 B:60.09 /60.00 @:0 B@:11
> 16:26:55.936:  T:200.00 /200.00 B:60.09 /60.00 @:41 B@:9 W:10
> 16:26:55.937: echo:busy: processing
> 16:26:56.595:  T:200.00 /200.00 B:60.05 /60.00 @:32 B@:16
> 16:26:56.936:  T:199.87 /200.00 B:60.05 /60.00 @:42 B@:12 W:9
> 16:26:57.595:  T:200.00 /200.00 B:60.05 /60.00 @:34 B@:17
> 16:26:57.936:  T:200.00 /200.00 B:60.05 /60.00 @:31 B@:12 W:8
> 16:26:57.936: echo:busy: processing
> 16:26:58.595:  T:199.87 /200.00 B:60.05 /60.00 @:50 B@:0
> 16:26:58.936:  T:200.00 /200.00 B:60.00 /60.00 @:24 B@:23 W:7
> 16:26:59.596:  T:200.18 /200.00 B:60.05 /60.00 @:16 B@:0
> 16:26:59.939:  T:200.00 /200.00 B:60.00 /60.00 @:34 B@:18 W:5
> 16:26:59.961: echo:busy: processing
> 16:27:00.596:  T:200.00 /200.00 B:60.00 /60.00 @:52 B@:14
> 16:27:00.938:  T:199.87 /200.00 B:60.00 /60.00 @:43 B@:14 W:4
> 16:27:01.595:  T:200.00 /200.00 B:59.95 /60.00 @:18 B@:22
> 16:27:01.938:  T:200.00 /200.00 B:59.95 /60.00 @:29 B@:26 W:3
> 16:27:01.960: echo:busy: processing
> 16:27:02.597:  T:200.00 /200.00 B:59.95 /60.00 @:28 B@:9
> 16:27:02.939:  T:200.00 /200.00 B:59.90 /60.00 @:30 B@:33 W:2
> 16:27:03.595:  T:200.18 /200.00 B:59.95 /60.00 @:19 B@:21
> 16:27:03.938:  T:199.87 /200.00 B:59.95 /60.00 @:65 B@:20 W:1
> 16:27:03.960: echo:busy: processing
> 16:27:04.595:  T:200.00 /200.00 B:59.90 /60.00 @:27 B@:19
> 16:27:04.939:  T:200.00 /200.00 B:59.95 /60.00 @:13 B@:0 W:0
> 16:27:05.595:  T:200.00 /200.00 B:59.90 /60.00 @:22 B@:37
> 16:27:05.931: ok N27 P63 B26
> 16:27:05.932: ok N28 P63 B27
> 16:27:05.932: ok P63 B28
> 16:27:05.932: X:0.00 Y:0.00 Z:0.00 E:0.00 Count X:0 Y:0 Z:64
> 16:27:05.932: ok N29 P63 B29
> 16:27:05.932: X:0.00 Y:0.00 Z:0.00 E:0.00 Count X:0 Y:0 Z:64
> 16:27:05.932: ok N30 P63 B30
> 16:27:05.932: ok N31 P62 B31
< 16:27:05.932: M117 Layer 0/595
< 16:27:05.932: N32 M107
< 16:27:05.933: N33 M204 S1000
< 16:27:05.933: N34 M205 X14.1 Y14.1
> 16:27:05.934: ok P62 B31
> 16:27:05.934: ok N32 P62 B31
> 16:27:05.934: ok N33 P62 B31
> 16:27:05.934: ok N34 P62 B31
< 16:27:05.934: N35 G0 F9000 X109.938 Y135.096 Z0.2
< 16:27:05.934: N36 G1 F3000 E0
< 16:27:05.934: N37 G1 X111.513 Y133.949 E0.07128
> 16:27:05.935: ok N35 P61 B31
< 16:27:05.936: N38 M73 P0 R66 Q0 S66
< 16:27:05.936: @excludeTimeOn
> 16:27:05.936: ok N36 P60 B30
< 16:27:05.936: @snapshot 0
> 16:27:05.937: ok N37 P59 B31
> 16:27:05.937: ok N38 P59 B31
< 16:27:05.937: N39 G1 F3000
< 16:27:05.937: @excludeTimeOff
< 16:27:05.937: N40 G1 X112.255 Y133.458 E0.10384
< 16:27:05.938: N41 G1 X113.305 Y132.912 E0.14714
> 16:27:05.938: ok N39 P59 B31
> 16:27:05.939: ok N40 P58 B31
< 16:27:05.939: N42 G1 X115.079 Y132.12 E0.21821
> 16:27:05.940: ok N41 P57 B31
> 16:27:05.940: ok N42 P56 B31
< 16:27:05.940: N43 G1 X115.907 Y131.794 E0.25077
< 16:27:05.941: N44 G1 X117.044 Y131.479 E0.29394
> 16:27:05.942: ok N43 P55 B31
< 16:27:05.942: N45 G1 X118.947 Y131.072 E0.36513
> 16:27:05.942: ok N44 P54 B31
< 16:27:05.942: N46 G1 X119.825 Y130.925 E0.3977
> 16:27:05.944: ok N45 P53 B31
> 16:27:05.944: ok N46 P52 B31
< 16:27:05.944: N47 G1 X121.008 Y130.853 E0.44106
< 16:27:05.944: N48 G1 X122.95 Y130.851 E0.51212
> 16:27:05.946: ok N47 P51 B31
< 16:27:05.946: N49 G1 X123.839 Y130.89 E0.54467
> 16:27:05.946: ok N48 P50 B31
< 16:27:05.946: N50 G1 X125.006 Y131.065 E0.58785
> 16:27:05.948: ok N49 P49 B31
> 16:27:05.948: ok N50 P48 B31
< 16:27:05.948: N51 G1 X126.909 Y131.467 E0.65901
< 16:27:05.948: N52 G1 X127.771 Y131.69 E0.69158
> 16:27:05.949: ok N51 P47 B31
< 16:27:05.949: N53 G1 X128.88 Y132.105 E0.7349
> 16:27:05.951: ok N52 P46 B31
> 16:27:05.951: ok N53 P45 B31
< 16:27:05.951: N54 G1 X130.657 Y132.894 E0.80604
< 16:27:05.951: N55 G1 X131.454 Y133.291 E0.83861
> 16:27:05.953: ok N54 P44 B31
< 16:27:05.953: N56 G1 X132.45 Y133.926 E0.88183
> 16:27:05.954: ok N55 P43 B31
> 16:27:05.954: ok N56 P42 B31
< 16:27:05.955: N57 G1 X134.027 Y135.069 E0.95309
< 16:27:05.955: N58 G1 X134.723 Y135.623 E0.98563
> 16:27:05.956: ok N57 P41 B31
< 16:27:05.956: N59 G1 X135.476 Y136.362 E1.02423
> 16:27:05.958: ok N58 P40 B31
> 16:27:05.958: ok N59 P39 B31
< 16:27:05.958: N60 G1 X136.03 Y135.794 E1.05326
< 16:27:05.958: N61 G1 X136.429 Y135.407 E1.0736
> 16:27:05.959: ok N60 P38 B31
< 16:27:05.959: N62 G1 X136.825 Y135.044 E1.09325
> 16:27:05.961: ok N61 P37 B31
> 16:27:05.961: ok N62 P36 B31
< 16:27:05.961: N63 G1 X137.419 Y134.542 E1.1217
< 16:27:05.961: N64 G1 X138.046 Y134.052 E1.15082
> 16:27:05.963: ok N63 P35 B31
< 16:27:05.963: N65 G1 X138.723 Y133.567 E1.18129
> 16:27:05.964: ok N64 P34 B31
> 16:27:05.964: ok N65 P33 B31
< 16:27:05.964: N66 G1 X139.382 Y133.136 E1.2101
< 16:27:05.965: N67 G1 X139.87 Y132.836 E1.23105
> 16:27:05.966: ok N66 P32 B31
< 16:27:05.966: N68 G1 X140.408 Y132.527 E1.25375
> 16:27:05.968: ok N67 P31 B31
> 16:27:05.968: ok N68 P30 B31
< 16:27:05.968: N69 G1 X141.108 Y132.162 E1.28264
< 16:27:05.969: N70 G1 X141.787 Y131.841 E1.31011
> 16:27:05.973: ok N69 P29 B31
> 16:27:05.973: ok N70 P28 B31
< 16:27:05.973: N71 G1 X142.398 Y131.576 E1.33448
< 16:27:05.974: N72 G1 X143.093 Y131.303 E1.3618
> 16:27:05.975: ok N71 P27 B31
< 16:27:05.975: N73 G1 X143.832 Y131.046 E1.39042
> 16:27:05.977: ok N72 P26 B31
> 16:27:05.977: ok N73 P25 B31
< 16:27:05.977: N74 G1 X144.529 Y130.834 E1.41708
< 16:27:05.977: N75 G1 X145.217 Y130.652 E1.44312
> 16:27:05.980: ok N74 P24 B31
> 16:27:05.980: ok N75 P23 B31
< 16:27:05.980: N76 G1 X145.983 Y130.478 E1.47185
< 16:27:05.980: N77 G1 X146.716 Y130.34 E1.49914
> 16:27:05.983: ok N76 P22 B31
> 16:27:05.983: ok N77 P21 B31
< 16:27:05.983: N78 G1 X147.42 Y130.235 E1.52518
< 16:27:05.983: N79 G1 X148.144 Y130.154 E1.55184
> 16:27:05.986: ok N78 P20 B31
> 16:27:05.986: ok N79 P19 B31
< 16:27:05.986: N80 G1 X149.231 Y130.073 E1.59172
< 16:27:05.986: N81 G1 X150.121 Y130.047 E1.62429
> 16:27:05.988: ok N80 P18 B31
> 16:27:05.989: ok N81 P17 B31
< 16:27:05.989: N82 G1 X150.617 Y130.067 E1.64245
< 16:27:05.989: N83 G1 X151.727 Y130.14 E1.68315
> 16:27:05.991: ok N82 P16 B31
> 16:27:05.991: ok N83 P16 B31
< 16:27:05.991: N84 G1 X152.63 Y130.242 E1.7164
< 16:27:05.992: N85 G1 X153.442 Y130.371 E1.74648
> 16:27:05.993: ok N84 P15 B31
< 16:27:05.993: N86 G1 X154.04 Y130.484 E1.76875
> 16:27:05.995: ok N85 P14 B31
> 16:27:05.995: ok N86 P13 B31
< 16:27:05.995: N87 G1 X154.723 Y130.636 E1.79435
< 16:27:05.995: N88 G1 X155.447 Y130.827 E1.82174
> 16:27:05.997: ok N87 P12 B31
> 16:27:05.997: ok N88 P11 B31
< 16:27:05.997: N89 G1 X156.116 Y131.03 E1.84732
< 16:27:05.998: N90 G1 X156.816 Y131.271 E1.8744
> 16:27:05.999: ok N89 P10 B31
< 16:27:05.999: N91 G1 X157.583 Y131.568 E1.9045
> 16:27:06.001: ok N90 P9 B31
> 16:27:06.001: ok N91 P8 B31
< 16:27:06.001: N92 G1 X158.292 Y131.875 E1.93276
< 16:27:06.001: N93 G1 X158.89 Y132.162 E1.95703
> 16:27:06.002: ok N92 P7 B31
< 16:27:06.002: N94 G1 X159.577 Y132.526 E1.98548
> 16:27:06.004: ok N93 P6 B31
> 16:27:06.004: ok N94 P5 B31
< 16:27:06.004: N95 G1 X160.383 Y132.994 E2.01958
< 16:27:06.004: N96 G1 X160.883 Y133.304 E2.0411
> 16:27:06.007: ok N95 P4 B30
> 16:27:06.007: ok N96 P3 B31
< 16:27:06.007: N97 G1 X161.628 Y133.798 E2.0738
< 16:27:06.007: N98 G1 X162.347 Y134.323 E2.10638
> 16:27:06.010: ok N97 P2 B30
> 16:27:06.010: ok N98 P1 B31
< 16:27:06.010: N99 G1 X162.775 Y134.686 E2.12691
< 16:27:06.010: N100 G1 X163.634 Y135.458 E2.16916
> 16:27:06.013: ok N99 P0 B30
< 16:27:06.013: N101 G1 X164.215 Y136.025 E2.19886
< 16:27:06.542: M117 ETA 17:33:14 day 26
> 16:27:06.596:  T:199.87 /200.00 B:59.90 /60.00 @:37 B@:15
> 16:27:07.279: ok N100 P0 B29
> 16:27:07.326: ok N101 P0 B30
< 16:27:07.326: N102 G1 X164.737 Y136.578 E2.22669
> 16:27:07.347: ok P0 B30
< 16:27:07.347: N103 G1 X165.211 Y137.118 E2.25297
> 16:27:07.373: ok N102 P0 B30
< 16:27:07.373: N104 G1 X165.679 Y137.692 E2.28007
> 16:27:07.595:  T:199.87 /200.00 B:59.84 /60.00 @:52 B@:40
> 16:27:08.595:  T:199.87 /200.00 B:59.90 /60.00 @:32 B@:26
> 16:27:09.612:  T:200.00 /200.00 B:59.90 /60.00 @:20 B@:20
> 16:27:10.607: echo:busy: processing
> 16:27:10.612:  T:200.00 /200.00 B:59.90 /60.00 @:20 B@:9
> 16:27:11.611:  T:199.87 /200.00 B:59.90 /60.00 @:40 B@:23
> 16:27:12.607: echo:busy: processing
> 16:27:12.612:  T:200.00 /200.00 B:59.90 /60.00 @:39 B@:32
> 16:27:13.613:  T:200.00 /200.00 B:59.90 /60.00 @:18 B@:39
> 16:27:14.608: echo:busy: processing
> 16:27:14.613:  T:200.00 /200.00 B:59.90 /60.00 @:28 B@:35
> 16:27:15.265: X:10.00 Y:290.00 Z:20.20 E:1.63 Count X:800 Y:23200 Z:8144
> 16:27:15.269:  T:199.87 /200.00 B:59.90 /60.00 @:57 B@:46 W:?
> 16:27:15.613:  T:200.00 /200.00 B:59.90 /60.00 @:28 B@:40
> 16:27:16.268:  T:199.87 /200.00 B:59.95 /60.00 @:43 B@:25 W:19
< 16:27:16.543: M117 ETE 01:06:08
> 16:27:16.607: echo:busy: processing
> 16:27:16.613:  T:200.00 /200.00 B:59.84 /60.00 @:29 B@:72
> 16:27:17.268:  T:200.00 /200.00 B:59.90 /60.00 @:36 B@:39 W:18
> 16:27:17.613:  T:200.18 /200.00 B:59.95 /60.00 @:0 B@:20
> 16:27:18.268:  T:200.00 /200.00 B:59.95 /60.00 @:49 B@:23 W:17
> 16:27:18.607: echo:busy: processing
> 16:27:18.612:  T:200.00 /200.00 B:60.00 /60.00 @:36 B@:14
> 16:27:19.269:  T:200.00 /200.00 B:59.95 /60.00 @:58 B@:38 W:16
> 16:27:19.612:  T:200.00 /200.00 B:59.95 /60.00 @:39 B@:36
> 16:27:20.269:  T:200.00 /200.00 B:59.95 /60.00 @:56 B@:34 W:15
> 16:27:20.607: echo:busy: processing
> 16:27:20.612:  T:200.00 /200.00 B:59.95 /60.00 @:38 B@:42
> 16:27:21.268:  T:200.18 /200.00 B:59.95 /60.00 @:6 B@:43 W:14
> 16:27:21.613:  T:200.00 /200.00 B:60.00 /60.00 @:48 B@:8
> 16:27:22.269:  T:200.18 /200.00 B:59.95 /60.00 @:17 B@:43 W:13
> 16:27:22.607: echo:busy: processing
> 16:27:22.613:  T:200.18 /200.00 B:60.00 /60.00 @:8 B@:20
> 16:27:23.268:  T:200.18 /200.00 B:60.05 /60.00 @:34 B@:12 W:12
> 16:27:23.613:  T:200.18 /200.00 B:60.05 /60.00 @:30 B@:14
> 16:27:24.269:  T:200.18 /200.00 B:60.00 /60.00 @:31 B@:34 W:11
> 16:27:24.607: echo:busy: processing
> 16:27:24.612:  T:200.18 /200.00 B:60.00 /60.00 @:29 B@:31
> 16:27:25.269:  T:200.36 /200.00 B:60.05 /60.00 @:10 B@:22 W:10
> 16:27:25.613:  T:200.18 /200.00 B:60.09 /60.00 @:50 B@:5
> 16:27:26.269:  T:200.36 /200.00 B:60.05 /60.00 @:9 B@:28 W:9
> 16:27:26.608: echo:busy: processing
> 16:27:26.612:  T:200.36 /200.00 B:60.05 /60.00 @:16 B@:19
> 16:27:27.269:  T:200.36 /200.00 B:60.00 /60.00 @:10 B@:34 W:8
> 16:27:27.612:  T:200.18 /200.00 B:60.00 /60.00 @:42 B@:34
> 16:27:28.269:  T:200.36 /200.00 B:60.05 /60.00 @:20 B@:36 W:7
> 16:27:28.608: echo:busy: processing
> 16:27:28.613:  T:200.00 /200.00 B:60.05 /60.00 @:69 B@:31
> 16:27:29.269:  T:200.00 /200.00 B:60.05 /60.00 @:39 B@:31 W:6
> 16:27:29.613:  T:200.00 /200.00 B:60.05 /60.00 @:52 B@:30
> 16:27:30.269:  T:200.18 /200.00 B:60.05 /60.00 @:18 B@:40 W:5
> 16:27:30.607: echo:busy: processing
> 16:27:30.613:  T:200.18 /200.00 B:60.05 /60.00 @:25 B@:32
> 16:27:31.269:  T:200.18 /200.00 B:60.05 /60.00 @:16 B@:31 W:4
> 16:27:31.613:  T:200.00 /200.00 B:60.14 /60.00 @:51 B@:0
> 16:27:32.269:  T:200.18 /200.00 B:60.05 /60.00 @:16 B@:35 W:3
> 16:27:32.608: echo:busy: processing
> 16:27:32.612:  T:200.00 /200.00 B:60.05 /60.00 @:53 B@:38
> 16:27:33.269:  T:200.00 /200.00 B:60.09 /60.00 @:27 B@:15 W:2
> 16:27:33.613:  T:200.00 /200.00 B:60.09 /60.00 @:29 B@:14
> 16:27:34.269:  T:200.18 /200.00 B:60.09 /60.00 @:0 B@:11 W:1
> 16:27:34.607: echo:busy: processing
> 16:27:34.614:  T:200.00 /200.00 B:60.05 /60.00 @:55 B@:36
> 16:27:35.268:  T:200.00 /200.00 B:60.09 /60.00 @:40 B@:16 W:0
> 16:27:38.614: Warning: Communication timeout - resetting communication buffer.
> 16:27:38.615: Connection status: Buffered:96, Manual Commands: 1, Job Commands: 5000
> 16:27:38.615: Buffer used:96 Enforced free byte:37 lines stored:3
< 16:27:38.615: M117 Layer 1/595
< 16:27:38.615: N105 G1 X166.116 Y138.27 E2.30658
< 16:27:38.616: N106 G1 X166.534 Y138.867 E2.33324
> 16:27:40.474: echo:busy: processing
> 16:27:40.523:  T:200.00 /200.00 B:60.05 /60.00 @:45 B@:31
> 16:27:41.523:  T:200.00 /200.00 B:60.09 /60.00 @:47 B@:14
> 16:27:41.690: echo:Insert filament and send M108
> 16:27:42.473: echo:busy: paused for user
> 16:27:42.524:  T:200.00 /200.00 B:60.05 /60.00 @:25 B@:31
> 16:27:43.543:  T:199.87 /200.00 B:60.05 /60.00 @:36 B@:25
> 16:27:44.474: echo:busy: paused for user
> 16:27:44.544:  T:199.87 /200.00 B:60.05 /60.00 @:53 B@:22
> 16:27:45.544:  T:199.87 /200.00 B:60.05 /60.00 @:30 B@:22
> 16:27:46.539: echo:busy: paused for user
> 16:27:46.544:  T:199.87 /200.00 B:60.05 /60.00 @:37 B@:19
> 16:27:47.544:  T:199.87 /200.00 B:60.00 /60.00 @:32 B@:32
> 16:27:48.539: echo:busy: paused for user
> 16:27:48.544:  T:199.87 /200.00 B:60.00 /60.00 @:50 B@:26
> 16:27:49.544:  T:200.00 /200.00 B:60.00 /60.00 @:28 B@:22
> 16:27:50.539: echo:busy: paused for user
> 16:27:50.544:  T:199.87 /200.00 B:60.00 /60.00 @:45 B@:29
> 16:27:51.544:  T:200.00 /200.00 B:60.00 /60.00 @:28 B@:29
> 16:27:52.539: echo:busy: paused for user
> 16:27:52.543:  T:199.87 /200.00 B:59.95 /60.00 @:38 B@:60
> 16:27:53.543:  T:200.00 /200.00 B:60.00 /60.00 @:47 B@:24
> 16:27:54.539: echo:busy: paused for user
> 16:27:54.543:  T:200.00 /200.00 B:60.00 /60.00 @:28 B@:24
> 16:27:55.544:  T:200.00 /200.00 B:60.00 /60.00 @:23 B@:24
> 16:27:56.539: echo:busy: paused for user
> 16:27:56.544:  T:200.00 /200.00 B:59.95 /60.00 @:36 B@:46
> 16:27:57.544:  T:200.18 /200.00 B:59.95 /60.00 @:0 B@:39
> 16:27:58.539: echo:busy: paused for user
> 16:27:58.544:  T:200.18 /200.00 B:60.00 /60.00 @:19 B@:18
> 16:27:59.544:  T:200.00 /200.00 B:60.00 /60.00 @:53 B@:22
> 16:28:00.539: echo:busy: paused for user
> 16:28:00.544:  T:200.00 /200.00 B:59.95 /60.00 @:49 B@:22
> 16:28:01.544:  T:200.18 /200.00 B:60.00 /60.00 @:7 B@:21
> 16:28:02.539: echo:busy: paused for user
> 16:28:02.544:  T:200.00 /200.00 B:59.95 /60.00 @:35 B@:30
> 16:28:03.544:  T:200.18 /200.00 B:59.95 /60.00 @:2 B@:39
> 16:28:04.539: echo:busy: paused for user
> 16:28:04.544:  T:200.00 /200.00 B:60.00 /60.00 @:61 B@:9
> 16:28:05.545:  T:200.00 /200.00 B:59.95 /60.00 @:23 B@:37
> 16:28:06.539: echo:busy: paused for user
> 16:28:06.544:  T:199.87 /200.00 B:60.00 /60.00 @:42 B@:18
> 16:28:07.544:  T:200.18 /200.00 B:59.95 /60.00 @:5 B@:51
> 16:28:08.539: echo:busy: paused for user
> 16:28:08.544:  T:200.36 /200.00 B:59.95 /60.00 @:0 B@:33
> 16:28:09.544:  T:200.00 /200.00 B:60.00 /60.00 @:28 B@:12
> 16:28:10.539: echo:busy: paused for user
> 16:28:10.544:  T:199.87 /200.00 B:59.95 /60.00 @:57 B@:40
> 16:28:11.544:  T:199.87 /200.00 B:60.00 /60.00 @:47 B@:23
> 16:28:12.539: echo:busy: paused for user
> 16:28:12.544:  T:200.00 /200.00 B:60.00 /60.00 @:8 B@:33
> 16:28:13.544:  T:199.87 /200.00 B:59.90 /60.00 @:58 B@:65
> 16:28:14.539: echo:busy: paused for user
> 16:28:14.544:  T:199.87 /200.00 B:60.00 /60.00 @:35 B@:28
> 16:28:15.544:  T:199.87 /200.00 B:60.00 /60.00 @:46 B@:29
> 16:28:16.539: echo:busy: paused for user
> 16:28:16.544:  T:200.00 /200.00 B:59.95 /60.00 @:33 B@:50
> 16:28:17.544:  T:200.00 /200.00 B:60.00 /60.00 @:51 B@:30
> 16:28:18.539: echo:busy: paused for user
> 16:28:18.544:  T:199.87 /200.00 B:59.95 /60.00 @:75 B@:62
> 16:28:19.544:  T:200.18 /200.00 B:60.00 /60.00 @:15 B@:13
> 16:28:20.539: echo:busy: paused for user
> 16:28:20.544:  T:200.18 /200.00 B:60.00 /60.00 @:24 B@:22
> 16:28:21.544:  T:200.00 /200.00 B:60.00 /60.00 @:32 B@:32
> 16:28:22.540: echo:busy: paused for user
> 16:28:22.545:  T:200.00 /200.00 B:60.00 /60.00 @:33 B@:32
> 16:28:23.544:  T:199.87 /200.00 B:60.05 /60.00 @:53 B@:13
> 16:28:24.540: echo:busy: paused for user
> 16:28:24.545:  T:199.87 /200.00 B:60.00 /60.00 @:49 B@:33
> 16:28:25.544:  T:200.00 /200.00 B:60.05 /60.00 @:22 B@:22
> 16:28:26.540: echo:busy: paused for user
> 16:28:26.545:  T:199.87 /200.00 B:60.00 /60.00 @:39 B@:33
> 16:28:26.692: echo:Send M108 to heat nozzle
> 16:28:27.544:  T:200.00 /200.00 B:60.00 /60.00 @:0 B@:30
> 16:28:28.540: echo:busy: paused for user

Thanks.
↧

Webcam wird nicht erkannt.

April 26, 2020, 7:29 am
$
0
0
Hallo ich habe mir gerade erst die Pro Version gekauft. Ich habe jetzt schon 2 Webcams ausprobiert Keine wird erkannt. Gibt es eine Liste welche funktionieren ?

↧

Hotend not heating

April 26, 2020, 3:44 pm
$
0
0
Hello

I just mounted an Ulticampy with two hotend and a hotbed.

Board : Arduino Mega and Ramps 1.4

The first hotend well work and heat.
The hotbed work and heat.
Both are well regulated in temperature

The second hotend do not heat. I start to heat and after a fee second it stop by security.

To see if it is an hardware issue I swap the two hotend. Still not working for the second one but the first one work (no issue on hotend and temperature sensor).

After that I change the Ramps to see if the mofset on the board is not dead but still not working.

I change the ARDUINO Mega to see if it is not the output commanding the mofset who is dead but steel not working.

So I have change all the hardware so it should be the software.

The only think that I do not understand is on the Ramps you have leds when the mofset are on.

For the first hotend and the hotbed the leds are bright and nice when the are heating.
For the second hotend the led is very low in brigthnes compare to the two other and it is blinking. Why I do not know????

Do some one face the same issue?
Can you support me?
↧
↧

How to send g-code to printer using Host

April 26, 2020, 4:45 pm
$
0
0
I am trying to calibrate my X and Y axes, and need to send the M503 command to the printer to see what the current values are. 

But when I use the Manual Control section of the GUI to send "M503" I get a "Unknown Command: Nxxxx M503".  So what is the correct incantation to send a command to the printer.  It's not obvious from the documentation.


↧

Extruder Numbering Confusion

April 26, 2020, 5:01 pm
$
0
0
I have recently re-flashed my Da Vinci Duo 2.0 with the Repetier firmware.  While I have been able to print out some objects, the numbering of the extruders is not intuitive.  The printer's menu refers to the "RIGHT" and "LEFT" extruders which make sense.  But the Host software refers to "Extruder 1" and "Extruder 2", and when I initially connect to the printer using the Host, I can see the command "SelectExtruder:0".  So which is which?  And how do I control which extruder will be used to print an object?
↧

`1234567` wrong password for the Repetier-Server Hotspot?

March 30, 2019, 6:05 pm
$
0
0
This is my first time trying to set up RS. 
I flashed V14 and it's booted. Hotspot created. 

I'm following https://www.repetier-server.com/download-images/
`RepetierServer and connect using the password 12345678`

Neither my computer nor my phone can connect. Authentification error it says. 



¯\_(ツ)_/¯

↧
Search

1143

April 27, 2020, 1:35 am
$
0
0
The World Health Group declared the Coronavirus (COVID-19) a pandemic on Wednesday, March eleven, 2020. https://trueallcbd.com/does-cbd-help-parkinson-s for medication on-line might not be only illegal, however dangerous. The American Medical Association and state boards of drugs and pharmacy have all condemned the observe of cyber medical doctors issuing online prescriptions as unacceptable medical care.
Latest studies point out that people who find themselves contaminated however would not have symptoms doubtless additionally play a job within the unfold of COVID-19.
Exam Limits: 5 Attempts You're allowed a most of 5 makes an attempt per jurisdiction or state to go the MPJE. After a failed attempt, you have to wait 30 days per jurisdiction or state to subsequent attempt the MPJE.
The scientists found that severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) was detectable in aerosols for as much as three hours, as much as four hours on copper, up to 24 hours on cardboard and up to two to 3 days on plastic and stainless steel.
Do We Really Know Why Doc And Marty McFly Have been Associates? looking for a web-based bachelor-degree degree in pharmacy have the choice to pursue a level in Pharmaceutical Science. Students wishing to enroll in a Bachelor's of Science in Pharmaceutical Research program will need to full pre-requisite science programs mandated by program.
The coronaviruses that trigger human illness are present in two genera: alphacoronaviruses (HCoV-229E, HCoV-NL63) and betacoronaviruses (HCoV-HKU1, HCoV-OC43, and the coronavirus associated with Severe Acute Respiratory Syndrome (SARS)).
Corona means crown in Latin, which is how coronaviruses obtained their name. Are generic medicines the identical? Scientists and researchers are exploring numerous avenues to provide you with medical therapies that can battle the novel coronavirus.
↧
↧

Running Repetier-Server without Admin privaliges

April 27, 2020, 8:33 am
$
0
0
How do I run Repetier-server without admin privileges on a Windows10 laptop.
I want to run the software on a works laptop.  Because of IT security admin privileges is reserved to HQ.
I cannot get Admin sign-in every time I want to run the software.
Please advise how this can be overcome. 
↧

New printer Creality CR10S PRO : connection ok but manual control no ok !!

February 21, 2019, 5:07 am
$
0
0
Hi,
CR10 S PRO and REPETIER HOST , the printer is well connected to Repetier (button "connec t", logs received...) but no functions are operational ??? (move the axis, home etc..) and none gcodes sent works..  An idea? Thanks
↧

Delta printer does not see endstops

April 27, 2020, 11:46 am
$
0
0
Hello guys,

Due to the quarantine periods I have dusted off my 3d printer that I've bought some 4 years ago.
Back then when I got it to print it worked for a bit and then started skipping layers.
I was told back then the firmware was flashed with a version of the Arduino IDE that was too "new".

The problem I had then, and now again, was that whenever I tell the printer to find it's home position it will go up (after finding the correct way to plug in the motor plugs to the board) and hit the end stops.
After it hits the endstops it will not stop going up.
The little screen that came with it shows that the endstop is on when they get hit, but it does not react accordingly.

I've tried several config files, including the ones that had been send to me by the company who sold me the printer back then.
I have also tried setting up a new firmware version using the repetier tool and with the information i could gather from the given config's.
Below is the result of that.
My last hope is that I could find some help with this problem here.


/*
    This file is part of Repetier-Firmware.

    Repetier-Firmware is free software: you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation, either version 3 of the License, or
    (at your option) any later version.

    Repetier-Firmware is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License
    along with Repetier-Firmware.  If not, see <http://www.gnu.org/licenses/>.

*/

#ifndef CONFIGURATION_H
#define CONFIGURATION_H

/**************** READ FIRST ************************

   This configuration file was created with the configuration tool. For that
   reason, it does not contain the same informations as the original Configuration.h file.
   It misses the comments and unused parts. Open this file file in the config tool
   to see and change the data. You can also upload it to newer/older versions. The system
   will silently add new options, so compilation continues to work.

   This file is optimized for version 0.92
   generator: http://www.repetier.com/firmware/v092/

   If you are in doubt which named functions use which pins on your board, please check the
   pins.h for the used name->pin assignments and your board documentation to verify it is
   as you expect.

*/

#define NUM_EXTRUDER 1
#define MOTHERBOARD 33
#include "pins.h"

// ################## EDIT THESE SETTINGS MANUALLY ################
// ################ END MANUAL SETTINGS ##########################

#undef FAN_BOARD_PIN
#define FAN_BOARD_PIN -1
#define BOARD_FAN_SPEED 255
#define FAN_THERMO_PIN -1
#define FAN_THERMO_MIN_PWM 128
#define FAN_THERMO_MAX_PWM 255
#define FAN_THERMO_MIN_TEMP 45
#define FAN_THERMO_MAX_TEMP 60
#define FAN_THERMO_THERMISTOR_PIN -1
#define FAN_THERMO_THERMISTOR_TYPE 1

//#define EXTERNALSERIAL  use Arduino serial library instead of build in. Requires more ram, has only 63 byte input buffer.
// Uncomment the following line if you are using Arduino compatible firmware made for Arduino version earlier then 1.0
// If it is incompatible you will get compiler errors about write functions not being compatible!
//#define COMPAT_PRE1
#define BLUETOOTH_SERIAL  -1
#define BLUETOOTH_BAUD  115200
#define MIXING_EXTRUDER 0

#define DRIVE_SYSTEM 3
#define XAXIS_STEPS_PER_MM 100
#define YAXIS_STEPS_PER_MM 100
#define ZAXIS_STEPS_PER_MM 100
#define EXTRUDER_FAN_COOL_TEMP 50
#define PDM_FOR_EXTRUDER 0
#define PDM_FOR_COOLER 0
#define DECOUPLING_TEST_MAX_HOLD_VARIANCE 20
#define DECOUPLING_TEST_MIN_TEMP_RISE 1
#define KILL_IF_SENSOR_DEFECT 0
#define RETRACT_ON_PAUSE 5
#define PAUSE_START_COMMANDS ""
#define PAUSE_END_COMMANDS ""
#define SHARED_EXTRUDER_HEATER 0
#define EXT0_X_OFFSET 0
#define EXT0_Y_OFFSET 0
#define EXT0_Z_OFFSET 0
#define EXT0_STEPS_PER_MM 518
#define EXT0_TEMPSENSOR_TYPE 8
#define EXT0_TEMPSENSOR_PIN TEMP_0_PIN
#define EXT0_HEATER_PIN HEATER_0_PIN
#define EXT0_STEP_PIN ORIG_E0_STEP_PIN
#define EXT0_DIR_PIN ORIG_E0_DIR_PIN
#define EXT0_INVERSE 0
#define EXT0_ENABLE_PIN ORIG_E0_ENABLE_PIN
#define EXT0_ENABLE_ON 0
#define EXT0_MIRROR_STEPPER 0
#define EXT0_STEP2_PIN ORIG_E0_STEP_PIN
#define EXT0_DIR2_PIN ORIG_E0_DIR_PIN
#define EXT0_INVERSE2 0
#define EXT0_ENABLE2_PIN ORIG_E0_ENABLE_PIN
#define EXT0_MAX_FEEDRATE 50
#define EXT0_MAX_START_FEEDRATE 20
#define EXT0_MAX_ACCELERATION 5000
#define EXT0_HEAT_MANAGER 3
#define EXT0_WATCHPERIOD 1
#define EXT0_PID_INTEGRAL_DRIVE_MAX 230
#define EXT0_PID_INTEGRAL_DRIVE_MIN 40
#define EXT0_PID_PGAIN_OR_DEAD_TIME 7
#define EXT0_PID_I 2
#define EXT0_PID_D 40
#define EXT0_PID_MAX 255
#define EXT0_ADVANCE_K 0
#define EXT0_ADVANCE_L 0
#define EXT0_ADVANCE_BACKLASH_STEPS 0
#define EXT0_WAIT_RETRACT_TEMP 150
#define EXT0_WAIT_RETRACT_UNITS 0
#define EXT0_SELECT_COMMANDS ""
#define EXT0_DESELECT_COMMANDS ""
#define EXT0_EXTRUDER_COOLER_PIN -1
#define EXT0_EXTRUDER_COOLER_SPEED 255
#define EXT0_DECOUPLE_TEST_PERIOD 12000
#define EXT0_JAM_PIN -1
#define EXT0_JAM_PULLUP 0

#define FEATURE_RETRACTION 1
#define AUTORETRACT_ENABLED 0
#define RETRACTION_LENGTH 3
#define RETRACTION_LONG_LENGTH 13
#define RETRACTION_SPEED 40
#define RETRACTION_Z_LIFT 0
#define RETRACTION_UNDO_EXTRA_LENGTH 0
#define RETRACTION_UNDO_EXTRA_LONG_LENGTH 0
#define RETRACTION_UNDO_SPEED 20
#define FILAMENTCHANGE_X_POS 0
#define FILAMENTCHANGE_Y_POS 0
#define FILAMENTCHANGE_Z_ADD  2
#define FILAMENTCHANGE_REHOME 1
#define FILAMENTCHANGE_SHORTRETRACT 5
#define FILAMENTCHANGE_LONGRETRACT 50
#define JAM_STEPS 220
#define JAM_SLOWDOWN_STEPS 320
#define JAM_SLOWDOWN_TO 70
#define JAM_ERROR_STEPS 500
#define JAM_MIN_STEPS 10
#define JAM_ACTION 1

#define RETRACT_DURING_HEATUP true
#define PID_CONTROL_RANGE 10
#define SKIP_M109_IF_WITHIN 2
#define SCALE_PID_TO_MAX 1
#define TEMP_HYSTERESIS 0
#define EXTRUDE_MAXLENGTH 160
#define NUM_TEMPS_USERTHERMISTOR0 0
#define USER_THERMISTORTABLE0 {}
#define NUM_TEMPS_USERTHERMISTOR1 0
#define USER_THERMISTORTABLE1 {}
#define NUM_TEMPS_USERTHERMISTOR2 0
#define USER_THERMISTORTABLE2 {}
#define GENERIC_THERM_VREF 5
#define GENERIC_THERM_NUM_ENTRIES 33
#define HEATER_PWM_SPEED 0

// ############# Heated bed configuration ########################

#define HAVE_HEATED_BED 0
#define HEATED_BED_MAX_TEMP 120
#define SKIP_M190_IF_WITHIN 3
#define HEATED_BED_SENSOR_TYPE 1
#define HEATED_BED_SENSOR_PIN TEMP_1_PIN
#define HEATED_BED_HEATER_PIN HEATER_1_PIN
#define HEATED_BED_SET_INTERVAL 5000
#define HEATED_BED_HEAT_MANAGER 0
#define HEATED_BED_PID_INTEGRAL_DRIVE_MAX 255
#define HEATED_BED_PID_INTEGRAL_DRIVE_MIN 80
#define HEATED_BED_PID_PGAIN_OR_DEAD_TIME   196
#define HEATED_BED_PID_IGAIN   33
#define HEATED_BED_PID_DGAIN 290
#define HEATED_BED_PID_MAX 255
#define HEATED_BED_DECOUPLE_TEST_PERIOD 300000
#define MIN_EXTRUDER_TEMP 150
#define MAXTEMP 275
#define MIN_DEFECT_TEMPERATURE -10
#define MAX_DEFECT_TEMPERATURE 290

// ##########################################################################################
// ##                             Laser configuration                                      ##
// ##########################################################################################

/*
  If the firmware is in laser mode, it can control a laser output to cut or engrave materials.
  Please use this feature only if you know about safety and required protection. Lasers are
  dangerous and can hurt or make you blind!!!

  The default laser driver only supports laser on and off. Here you control the eíntensity with
  your feedrate. For exchangeable diode lasers this is normally enough. If you need more control
  you can set the intensity in a range 0-255 with a custom extension to the driver. See driver.h
  and comments on how to extend the functions non invasive with our event system.

  If you have a laser - powder system you will like your E override. If moves contain a
  increasing extruder position it will laser that move. With this trick you can
  use existing fdm slicers to laser the output. Laser width is extrusion width.

  Other tools may use M3 and M5 to enable/disable laser. Here G1/G2/G3 moves have laser enabled
  and G0 moves have it disables.

  In any case, laser only enables while moving. At the end of a move it gets
  automatically disabled.
*/

#define SUPPORT_LASER 0
#define LASER_PIN -1
#define LASER_ON_HIGH 1

// ##                              CNC configuration                                       ##

/*
  If the firmware is in CNC mode, it can control a mill with M3/M4/M5. It works
  similar to laser mode, but mill keeps enabled during G0 moves and it allows
  setting rpm (only with event extension that supports this) and milling direction.
  It also can add a delay to wait for spindle to run on full speed.
*/

#define SUPPORT_CNC 0
#define CNC_WAIT_ON_ENABLE 300
#define CNC_WAIT_ON_DISABLE 0
#define CNC_ENABLE_PIN -1
#define CNC_ENABLE_WITH 1
#define CNC_DIRECTION_PIN -1
#define CNC_DIRECTION_CW 1


#define DEFAULT_PRINTER_MODE 0

// ################ Endstop configuration #####################

#define ENDSTOP_PULLUP_X_MIN true
#define ENDSTOP_X_MIN_INVERTING true
#define MIN_HARDWARE_ENDSTOP_X true
#define ENDSTOP_PULLUP_Y_MIN true
#define ENDSTOP_Y_MIN_INVERTING true
#define MIN_HARDWARE_ENDSTOP_Y true
#define ENDSTOP_PULLUP_Z_MIN false
#define ENDSTOP_Z_MIN_INVERTING false
#define MIN_HARDWARE_ENDSTOP_Z true
#define ENDSTOP_PULLUP_X_MAX false
#define ENDSTOP_X_MAX_INVERTING false
#define MAX_HARDWARE_ENDSTOP_X false
#define ENDSTOP_PULLUP_Y_MAX false
#define ENDSTOP_Y_MAX_INVERTING false
#define MAX_HARDWARE_ENDSTOP_Y false
#define ENDSTOP_PULLUP_Z_MAX false
#define ENDSTOP_Z_MAX_INVERTING false
#define MAX_HARDWARE_ENDSTOP_Z false
#define max_software_endstop_r true

#define min_software_endstop_x true
#define min_software_endstop_y true
#define min_software_endstop_z true
#define max_software_endstop_x false
#define max_software_endstop_y false
#define max_software_endstop_z false
#define ENDSTOP_X_BACK_MOVE 10
#define ENDSTOP_Y_BACK_MOVE 10
#define ENDSTOP_Z_BACK_MOVE 10
#define ENDSTOP_X_RETEST_REDUCTION_FACTOR 3
#define ENDSTOP_Y_RETEST_REDUCTION_FACTOR 3
#define ENDSTOP_Z_RETEST_REDUCTION_FACTOR 3
#define ENDSTOP_X_BACK_ON_HOME 10
#define ENDSTOP_Y_BACK_ON_HOME 10
#define ENDSTOP_Z_BACK_ON_HOME 10
#define ALWAYS_CHECK_ENDSTOPS 1

// ################# XYZ movements ###################

#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define DISABLE_X 0
#define DISABLE_Y 0
#define DISABLE_Z 0
#define DISABLE_E 0
#define INVERT_X_DIR 0
#define INVERT_Y_DIR 0
#define INVERT_Z_DIR 0
#define X_HOME_DIR 1
#define Y_HOME_DIR 1
#define Z_HOME_DIR 1
#define X_MAX_LENGTH 200
#define Y_MAX_LENGTH 200
#define Z_MAX_LENGTH 228.5
#define X_MIN_POS 0
#define Y_MIN_POS 0
#define Z_MIN_POS 0
#define DISTORTION_CORRECTION 0
#define DISTORTION_CORRECTION_POINTS 5
#define DISTORTION_CORRECTION_R 100
#define DISTORTION_PERMANENT 1
#define DISTORTION_UPDATE_FREQUENCY 15
#define DISTORTION_START_DEGRADE 0.5
#define DISTORTION_END_HEIGHT 1
#define DISTORTION_EXTRAPOLATE_CORNERS 0
#define DISTORTION_XMIN 10
#define DISTORTION_YMIN 10
#define DISTORTION_XMAX 190
#define DISTORTION_YMAX 190

// ##########################################################################################
// ##                           Movement settings                                          ##
// ##########################################################################################

#define FEATURE_BABYSTEPPING 1
#define BABYSTEP_MULTIPLICATOR 1

#define DELTA_SEGMENTS_PER_SECOND_PRINT 180 // Move accurate setting for print moves
#define DELTA_SEGMENTS_PER_SECOND_MOVE 70 // Less accurate setting for other moves
#define EXACT_DELTA_MOVES 1

// Delta settings
#define DELTA_DIAGONAL_ROD 214 // mm
#define DELTA_ALPHA_A 210
#define DELTA_ALPHA_B 330
#define DELTA_ALPHA_C 90
#define DELTA_RADIUS_CORRECTION_A 0
#define DELTA_RADIUS_CORRECTION_B 0
#define DELTA_RADIUS_CORRECTION_C 0
#define DELTA_DIAGONAL_CORRECTION_A 0
#define DELTA_DIAGONAL_CORRECTION_B 0
#define DELTA_DIAGONAL_CORRECTION_C 0
#define END_EFFECTOR_HORIZONTAL_OFFSET 0
#define CARRIAGE_HORIZONTAL_OFFSET 0
#define DELTA_MAX_RADIUS 140
#define ROD_RADIUS 116
#define PRINTER_RADIUS 116
#define DELTA_HOME_ON_POWER 0
#define STEP_COUNTER
#define DELTA_X_ENDSTOP_OFFSET_STEPS 0
#define DELTA_Y_ENDSTOP_OFFSET_STEPS 0
#define DELTA_Z_ENDSTOP_OFFSET_STEPS 0
#define DELTA_FLOOR_SAFETY_MARGIN_MM 90
//#define SOFTWARE_LEVELING

#define DELTASEGMENTS_PER_PRINTLINE 24
#define STEPPER_INACTIVE_TIME 360L
#define MAX_INACTIVE_TIME 0L
#define MAX_FEEDRATE_X 300
#define MAX_FEEDRATE_Y 300
#define MAX_FEEDRATE_Z 300
#define HOMING_FEEDRATE_X 40
#define HOMING_FEEDRATE_Y 40
#define HOMING_FEEDRATE_Z 40
#define HOMING_ORDER HOME_ORDER_ZXY
#define ZHOME_MIN_TEMPERATURE 0
#define ZHOME_HEAT_ALL 1
#define ZHOME_HEAT_HEIGHT 20
#define ZHOME_X_POS 999999
#define ZHOME_Y_POS 999999
#define ENABLE_BACKLASH_COMPENSATION 0
#define X_BACKLASH 0
#define Y_BACKLASH 0
#define Z_BACKLASH 0
#define RAMP_ACCELERATION 1
#define STEPPER_HIGH_DELAY 0
#define DIRECTION_DELAY 0
#define STEP_DOUBLER_FREQUENCY 12000
#define ALLOW_QUADSTEPPING 1
#define DOUBLE_STEP_DELAY 1 // time in microseconds
#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X 3000
#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Y 3000
#define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Z 3000
#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X 1000
#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Y 1000
#define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Z 1000
#define INTERPOLATE_ACCELERATION_WITH_Z 0
#define ACCELERATION_FACTOR_TOP 100
#define MAX_JERK 20
#define MAX_ZJERK 0.3
#define PRINTLINE_CACHE_SIZE 16
#define MOVE_CACHE_LOW 10
#define LOW_TICKS_PER_MOVE 250000
#define EXTRUDER_SWITCH_XY_SPEED 100
#define DUAL_X_AXIS 0
#define FEATURE_TWO_XSTEPPER 0
#define X2_STEP_PIN   ORIG_E1_STEP_PIN
#define X2_DIR_PIN    ORIG_E1_DIR_PIN
#define X2_ENABLE_PIN ORIG_E1_ENABLE_PIN
#define FEATURE_TWO_YSTEPPER 0
#define Y2_STEP_PIN   ORIG_E1_STEP_PIN
#define Y2_DIR_PIN    ORIG_E1_DIR_PIN
#define Y2_ENABLE_PIN ORIG_E1_ENABLE_PIN
#define FEATURE_TWO_ZSTEPPER 0
#define Z2_STEP_PIN   ORIG_E1_STEP_PIN
#define Z2_DIR_PIN    ORIG_E1_DIR_PIN
#define Z2_ENABLE_PIN ORIG_E1_ENABLE_PIN
#define FEATURE_THREE_ZSTEPPER 0
#define Z3_STEP_PIN   ORIG_E2_STEP_PIN
#define Z3_DIR_PIN    ORIG_E2_DIR_PIN
#define Z3_ENABLE_PIN ORIG_E2_ENABLE_PIN
#define FEATURE_DITTO_PRINTING 0
#define USE_ADVANCE 0
#define ENABLE_QUADRATIC_ADVANCE 0


// ################# Misc. settings ##################

#define BAUDRATE 115200
#define ENABLE_POWER_ON_STARTUP 1
#define POWER_INVERTING 0
#define KILL_METHOD 1
#define ACK_WITH_LINENUMBER 1
#define WAITING_IDENTIFIER "wait"
#define ECHO_ON_EXECUTE 1
#define EEPROM_MODE 1
#undef PS_ON_PIN
#define PS_ON_PIN ORIG_PS_ON_PIN
#define JSON_OUTPUT 0

/* ======== Servos =======
  Control the servos with
  M340 P<servoId> S<pulseInUS>   / ServoID = 0..3  pulseInUs = 500..2500
  Servos are controlled by a pulse width normally between 500 and 2500 with 1500ms in center position. 0 turns servo off.
  WARNING: Servos can draw a considerable amount of current. Make sure your system can handle this or you may risk your hardware!
*/
#define FEATURE_SERVO 0
#define SERVO0_PIN 11
#define SERVO1_PIN -1
#define SERVO2_PIN -1
#define SERVO3_PIN -1
#define SERVO0_NEUTRAL_POS  -1
#define SERVO1_NEUTRAL_POS  -1
#define SERVO2_NEUTRAL_POS  -1
#define SERVO3_NEUTRAL_POS  -1
#define UI_SERVO_CONTROL 0
#define FAN_KICKSTART_TIME  200

#define FEATURE_WATCHDOG 0

// #################### Z-Probing #####################

#define Z_PROBE_Z_OFFSET 0
#define Z_PROBE_Z_OFFSET_MODE 0
#define UI_BED_COATING 1
#define FEATURE_Z_PROBE 0
#define Z_PROBE_BED_DISTANCE 10
#define Z_PROBE_PIN -1
#define Z_PROBE_PULLUP 0
#define Z_PROBE_ON_HIGH 0
#define Z_PROBE_X_OFFSET 0
#define Z_PROBE_Y_OFFSET 0
#define Z_PROBE_WAIT_BEFORE_TEST 0
#define Z_PROBE_SPEED 2
#define Z_PROBE_XY_SPEED 150
#define Z_PROBE_SWITCHING_DISTANCE 1
#define Z_PROBE_REPETITIONS 1
#define Z_PROBE_HEIGHT 40
#define Z_PROBE_START_SCRIPT ""
#define Z_PROBE_FINISHED_SCRIPT ""
#define Z_PROBE_REQUIRES_HEATING 0
#define Z_PROBE_MIN_TEMPERATURE 150
#define FEATURE_AUTOLEVEL 1
#define Z_PROBE_X1 20
#define Z_PROBE_Y1 20
#define Z_PROBE_X2 160
#define Z_PROBE_Y2 20
#define Z_PROBE_X3 100
#define Z_PROBE_Y3 160
#define BED_LEVELING_METHOD 0
#define BED_CORRECTION_METHOD 0
#define BED_LEVELING_GRID_SIZE 5
#define BED_LEVELING_REPETITIONS 5
#define BED_MOTOR_1_X 0
#define BED_MOTOR_1_Y 0
#define BED_MOTOR_2_X 200
#define BED_MOTOR_2_Y 0
#define BED_MOTOR_3_X 100
#define BED_MOTOR_3_Y 200
#define BENDING_CORRECTION_A 0
#define BENDING_CORRECTION_B 0
#define BENDING_CORRECTION_C 0
#define FEATURE_AXISCOMP 0
#define AXISCOMP_TANXY 0
#define AXISCOMP_TANYZ 0
#define AXISCOMP_TANXZ 0

#ifndef SDSUPPORT  // Some boards have sd support on board. These define the values already in pins.h
#define SDSUPPORT 0
#undef SDCARDDETECT
#define SDCARDDETECT -1
#define SDCARDDETECTINVERTED 0
#endif
#define SD_EXTENDED_DIR 1 /** Show extended directory including file length. Don't use this with Pronterface! */
#define SD_RUN_ON_STOP ""
#define SD_STOP_HEATER_AND_MOTORS_ON_STOP 1
#define ARC_SUPPORT 1
#define FEATURE_MEMORY_POSITION 1
#define FEATURE_CHECKSUM_FORCED 0
#define FEATURE_FAN_CONTROL 1
#define FEATURE_FAN2_CONTROL 0
#define FEATURE_CONTROLLER 2
#define ADC_KEYPAD_PIN -1
#define LANGUAGE_EN_ACTIVE 1
#define LANGUAGE_DE_ACTIVE 0
#define LANGUAGE_NL_ACTIVE 0
#define LANGUAGE_PT_ACTIVE 0
#define LANGUAGE_IT_ACTIVE 0
#define LANGUAGE_ES_ACTIVE 0
#define LANGUAGE_FI_ACTIVE 0
#define LANGUAGE_SE_ACTIVE 0
#define LANGUAGE_FR_ACTIVE 0
#define LANGUAGE_CZ_ACTIVE 0
#define LANGUAGE_PL_ACTIVE 0
#define LANGUAGE_TR_ACTIVE 0
#define UI_PRINTER_NAME "Kossel"
#define UI_PRINTER_COMPANY "RN"
#define UI_PAGES_DURATION 4000
#define UI_ANIMATION 0
#define UI_SPEEDDEPENDENT_POSITIONING 0
#define UI_DISABLE_AUTO_PAGESWITCH 1
#define UI_AUTORETURN_TO_MENU_AFTER 30000
#define FEATURE_UI_KEYS 0
#define UI_ENCODER_SPEED 1
#define UI_REVERSE_ENCODER 0
#define UI_KEY_BOUNCETIME 10
#define UI_KEY_FIRST_REPEAT 500
#define UI_KEY_REDUCE_REPEAT 50
#define UI_KEY_MIN_REPEAT 50
#define FEATURE_BEEPER 1
#define CASE_LIGHTS_PIN -1
#define CASE_LIGHT_DEFAULT_ON 1
#define UI_START_SCREEN_DELAY 1000
#define UI_DYNAMIC_ENCODER_SPEED 1
/**
  Beeper sound definitions for short beeps during key actions
  and longer beeps for important actions.
  Parameter is delay in microseconds and the secons is the number of repetitions.
  Values must be in range 1..255
*/
#define BEEPER_SHORT_SEQUENCE 2,2
#define BEEPER_LONG_SEQUENCE 8,8
#define UI_SET_PRESET_HEATED_BED_TEMP_PLA 60
#define UI_SET_PRESET_EXTRUDER_TEMP_PLA   190
#define UI_SET_PRESET_HEATED_BED_TEMP_ABS 110
#define UI_SET_PRESET_EXTRUDER_TEMP_ABS   240
#define UI_SET_MIN_HEATED_BED_TEMP  30
#define UI_SET_MAX_HEATED_BED_TEMP 120
#define UI_SET_MIN_EXTRUDER_TEMP   170
#define UI_SET_MAX_EXTRUDER_TEMP   260
#define UI_SET_EXTRUDER_FEEDRATE 2
#define UI_SET_EXTRUDER_RETRACT_DISTANCE 3


#define NUM_MOTOR_DRIVERS 0



#endif

/* Below you will find the configuration string, that created this Configuration.h

  ========== Start configuration string ==========
  {
    "editMode": 2,
    "processor": 0,
    "baudrate": 115200,
    "bluetoothSerial": -1,
    "bluetoothBaudrate": 115200,
    "xStepsPerMM": 100,
    "yStepsPerMM": 100,
    "zStepsPerMM": 100,
    "xInvert": 0,
    "xInvertEnable": 0,
    "eepromMode": 1,
    "yInvert": 0,
    "yInvertEnable": 0,
    "zInvert": 0,
    "zInvertEnable": 0,
    "extruder": [
        {
            "id": 0,
            "heatManager": 3,
            "pidDriveMin": 40,
            "pidDriveMax": 230,
            "pidMax": 255,
            "sensorType": 8,
            "sensorPin": "TEMP_0_PIN",
            "heaterPin": "HEATER_0_PIN",
            "maxFeedrate": 50,
            "startFeedrate": 20,
            "invert": "0",
            "invertEnable": "0",
            "acceleration": 5000,
            "watchPeriod": 1,
            "pidP": 7,
            "pidI": 2,
            "pidD": 40,
            "advanceK": 0,
            "advanceL": 0,
            "waitRetractTemp": 150,
            "waitRetractUnits": 0,
            "waitRetract": 0,
            "stepsPerMM": 518,
            "coolerPin": -1,
            "coolerSpeed": 255,
            "selectCommands": "",
            "deselectCommands": "",
            "xOffset": 0,
            "yOffset": 0,
            "zOffset": 0,
            "xOffsetSteps": 0,
            "yOffsetSteps": 0,
            "zOffsetSteps": 0,
            "stepper": {
                "name": "Extruder 0",
                "step": "ORIG_E0_STEP_PIN",
                "dir": "ORIG_E0_DIR_PIN",
                "enable": "ORIG_E0_ENABLE_PIN"
            },
            "advanceBacklashSteps": 0,
            "decoupleTestPeriod": 12,
            "jamPin": -1,
            "jamPullup": "0",
            "mirror": "0",
            "invert2": "0",
            "stepper2": {
                "name": "Extruder 0",
                "step": "ORIG_E0_STEP_PIN",
                "dir": "ORIG_E0_DIR_PIN",
                "enable": "ORIG_E0_ENABLE_PIN"
            },
            "inverse": 0
        }
    ],
    "uiLanguage": 0,
    "uiController": 0,
    "xMinEndstop": 0,
    "yMinEndstop": 0,
    "zMinEndstop": 0,
    "xMaxEndstop": 2,
    "yMaxEndstop": 2,
    "zMaxEndstop": 2,
    "motherboard": 33,
    "driveSystem": 3,
    "xMaxSpeed": 300,
    "xHomingSpeed": 40,
    "xTravelAcceleration": 1000,
    "xPrintAcceleration": 1000,
    "yMaxSpeed": 300,
    "yHomingSpeed": 40,
    "yTravelAcceleration": 1000,
    "yPrintAcceleration": 1000,
    "zMaxSpeed": 300,
    "zHomingSpeed": 40,
    "zTravelAcceleration": 1000,
    "zPrintAcceleration": 1000,
    "xMotor": {
        "name": "X motor",
        "step": "ORIG_X_STEP_PIN",
        "dir": "ORIG_X_DIR_PIN",
        "enable": "ORIG_X_ENABLE_PIN"
    },
    "yMotor": {
        "name": "Y motor",
        "step": "ORIG_Y_STEP_PIN",
        "dir": "ORIG_Y_DIR_PIN",
        "enable": "ORIG_Y_ENABLE_PIN"
    },
    "zMotor": {
        "name": "Z motor",
        "step": "ORIG_Z_STEP_PIN",
        "dir": "ORIG_Z_DIR_PIN",
        "enable": "ORIG_Z_ENABLE_PIN"
    },
    "enableBacklash": "0",
    "backlashX": 0,
    "backlashY": 0,
    "backlashZ": 0,
    "stepperInactiveTime": 360,
    "maxInactiveTime": 0,
    "xMinPos": 0,
    "yMinPos": 0,
    "zMinPos": 0,
    "xLength": 200,
    "yLength": 200,
    "zLength": 228.5,
    "alwaysCheckEndstops": "1",
    "disableX": "0",
    "disableY": "0",
    "disableZ": "0",
    "disableE": "0",
    "xHomeDir": "-1",
    "yHomeDir": "-1",
    "zHomeDir": 1,
    "xEndstopBack": 1,
    "yEndstopBack": 1,
    "zEndstopBack": 0,
    "deltaSegmentsPerSecondPrint": 180,
    "deltaSegmentsPerSecondTravel": 70,
    "deltaDiagonalRod": 214,
    "deltaHorizontalRadius": 116,
    "deltaAlphaA": 210,
    "deltaAlphaB": 330,
    "deltaAlphaC": 90,
    "deltaDiagonalCorrA": 0,
    "deltaDiagonalCorrB": 0,
    "deltaDiagonalCorrC": 0,
    "deltaMaxRadius": 140,
    "deltaFloorSafetyMarginMM": 15,
    "deltaRadiusCorrA": 0,
    "deltaRadiusCorrB": 0,
    "deltaRadiusCorrC": 0,
    "deltaXOffsetSteps": 0,
    "deltaYOffsetSteps": 0,
    "deltaZOffsetSteps": 0,
    "deltaSegmentsPerLine": 24,
    "stepperHighDelay": 0,
    "directionDelay": 0,
    "stepDoublerFrequency": 12000,
    "allowQuadstepping": "1",
    "doubleStepDelay": 1,
    "maxJerk": 20,
    "maxZJerk": 0.3,
    "moveCacheSize": 16,
    "moveCacheLow": 10,
    "lowTicksPerMove": 250000,
    "enablePowerOnStartup": "1",
    "echoOnExecute": "1",
    "sendWaits": "1",
    "ackWithLineNumber": "1",
    "killMethod": 1,
    "useAdvance": "0",
    "useQuadraticAdvance": "0",
    "powerInverting": 0,
    "mirrorX": "0",
    "mirrorXMotor": {
        "name": "Extruder 1",
        "step": "ORIG_E1_STEP_PIN",
        "dir": "ORIG_E1_DIR_PIN",
        "enable": "ORIG_E1_ENABLE_PIN"
    },
    "mirrorY": "0",
    "mirrorYMotor": {
        "name": "Extruder 1",
        "step": "ORIG_E1_STEP_PIN",
        "dir": "ORIG_E1_DIR_PIN",
        "enable": "ORIG_E1_ENABLE_PIN"
    },
    "mirrorZ": 0,
    "mirrorZMotor": {
        "name": "Extruder 1",
        "step": "ORIG_E1_STEP_PIN",
        "dir": "ORIG_E1_DIR_PIN",
        "enable": "ORIG_E1_ENABLE_PIN"
    },
    "mirrorZ3": "0",
    "mirrorZ3Motor": {
        "name": "Extruder 2",
        "step": "ORIG_E2_STEP_PIN",
        "dir": "ORIG_E2_DIR_PIN",
        "enable": "ORIG_E2_ENABLE_PIN"
    },
    "dittoPrinting": "0",
    "featureServos": "0",
    "servo0Pin": 11,
    "servo1Pin": -1,
    "servo2Pin": -1,
    "servo3Pin": -1,
    "featureWatchdog": "0",
    "hasHeatedBed": "0",
    "enableZProbing": "0",
    "extrudeMaxLength": 160,
    "homeOrder": "HOME_ORDER_ZXY",
    "featureController": 2,
    "uiPrinterName": "RepRap.cn",
    "uiPrinterCompany": "HE3D",
    "uiPagesDuration": 4000,
    "uiAnimation": "0",
    "uiDisablePageswitch": "1",
    "uiAutoReturnAfter": 30000,
    "featureKeys": "0",
    "uiEncoderSpeed": 1,
    "uiReverseEncoder": "0",
    "uiKeyBouncetime": 10,
    "uiKeyFirstRepeat": 500,
    "uiKeyReduceRepeat": 50,
    "uiKeyMinRepeat": 50,
    "featureBeeper": "0",
    "uiPresetBedTempPLA": 60,
    "uiPresetBedABS": 110,
    "uiPresetExtruderPLA": 190,
    "uiPresetExtruderABS": 240,
    "uiMinHeatedBed": 30,
    "uiMaxHeatedBed": 120,
    "uiMinEtxruderTemp": 170,
    "uiMaxExtruderTemp": 260,
    "uiExtruderFeedrate": 2,
    "uiExtruderRetractDistance": 3,
    "uiSpeeddependentPositioning": "0",
    "maxBedTemperature": 120,
    "bedSensorType": 1,
    "bedSensorPin": "TEMP_1_PIN",
    "bedHeaterPin": "HEATER_1_PIN",
    "bedHeatManager": 0,
    "bedUpdateInterval": 5000,
    "bedPidDriveMin": 80,
    "bedPidDriveMax": 255,
    "bedPidP": 196,
    "bedPidI": 33,
    "bedPidD": 290,
    "bedPidMax": 255,
    "bedDecoupleTestPeriod": 300,
    "caseLightPin": -1,
    "caseLightDefaultOn": "1",
    "bedSkipIfWithin": 3,
    "gen1T0": 25,
    "gen1R0": 100000,
    "gen1Beta": 4036,
    "gen1MinTemp": -20,
    "gen1MaxTemp": 300,
    "gen1R1": 0,
    "gen1R2": 4700,
    "gen2T0": 25,
    "gen2R0": 100000,
    "gen2Beta": 4036,
    "gen2MinTemp": -20,
    "gen2MaxTemp": 300,
    "gen2R1": 0,
    "gen2R2": 4700,
    "gen3T0": 25,
    "gen3R0": 100000,
    "gen3Beta": 4036,
    "gen3MinTemp": -20,
    "gen3MaxTemp": 300,
    "gen3R1": 0,
    "gen3R2": 4700,
    "userTable0": {
        "r1": 0,
        "r2": 4700,
        "temps": [],
        "numEntries": 0
    },
    "userTable1": {
        "r1": 0,
        "r2": 4700,
        "temps": [],
        "numEntries": 0
    },
    "userTable2": {
        "r1": 0,
        "r2": 4700,
        "temps": [],
        "numEntries": 0
    },
    "tempHysteresis": 0,
    "pidControlRange": 10,
    "skipM109Within": 2,
    "extruderFanCoolTemp": 50,
    "minTemp": 150,
    "maxTemp": 275,
    "minDefectTemp": -10,
    "maxDefectTemp": 290,
    "arcSupport": "1",
    "featureMemoryPositionWatchdog": "1",
    "forceChecksum": "0",
    "sdExtendedDir": "1",
    "featureFanControl": "1",
    "fanPin": "ORIG_FAN_PIN",
    "featureFan2Control": "0",
    "fan2Pin": "ORIG_FAN2_PIN",
    "fanThermoPin": -1,
    "fanThermoMinPWM": 128,
    "fanThermoMaxPWM": 255,
    "fanThermoMinTemp": 45,
    "fanThermoMaxTemp": 60,
    "fanThermoThermistorPin": -1,
    "fanThermoThermistorType": 1,
    "scalePidToMax": "1",
    "zProbePin": -1,
    "zProbeBedDistance": 10,
    "zProbePullup": "0",
    "zProbeOnHigh": "0",
    "zProbeXOffset": 0,
    "zProbeYOffset": 0,
    "zProbeWaitBeforeTest": "0",
    "zProbeSpeed": 2,
    "zProbeXYSpeed": 150,
    "zProbeHeight": 40,
    "zProbeStartScript": "",
    "zProbeFinishedScript": "",
    "featureAutolevel": "1",
    "zProbeX1": 20,
    "zProbeY1": 20,
    "zProbeX2": 160,
    "zProbeY2": 20,
    "zProbeX3": 100,
    "zProbeY3": 160,
    "zProbeSwitchingDistance": 1,
    "zProbeRepetitions": 1,
    "sdSupport": "0",
    "sdCardDetectPin": -1,
    "sdCardDetectInverted": "0",
    "uiStartScreenDelay": 1000,
    "xEndstopBackMove": 5,
    "yEndstopBackMove": 5,
    "zEndstopBackMove": 5,
    "xEndstopRetestFactor": 3,
    "yEndstopRetestFactor": 3,
    "zEndstopRetestFactor": 3,
    "xMinPin": "ORIG_X_MIN_PIN",
    "yMinPin": "ORIG_Y_MIN_PIN",
    "zMinPin": "ORIG_Z_MIN_PIN",
    "xMaxPin": "ORIG_X_MAX_PIN",
    "yMaxPin": "ORIG_Y_MAX_PIN",
    "zMaxPin": "ORIG_Z_MAX_PIN",
    "deltaHomeOnPower": "0",
    "fanBoardPin": -1,
    "heaterPWMSpeed": 0,
    "featureBabystepping": "1",
    "babystepMultiplicator": 1,
    "pdmForHeater": "0",
    "pdmForCooler": "0",
    "psOn": "ORIG_PS_ON_PIN",
    "mixingExtruder": "0",
    "decouplingTestMaxHoldVariance": 20,
    "decouplingTestMinTempRise": 1,
    "featureAxisComp": "0",
    "axisCompTanXY": 0,
    "axisCompTanXZ": 0,
    "axisCompTanYZ": 0,
    "retractOnPause": 5,
    "pauseStartCommands": "",
    "pauseEndCommands": "",
    "distortionCorrection": "0",
    "distortionCorrectionPoints": 5,
    "distortionCorrectionR": 100,
    "distortionPermanent": "1",
    "distortionUpdateFrequency": 15,
    "distortionStartDegrade": 0.5,
    "distortionEndDegrade": 1,
    "distortionExtrapolateCorners": "0",
    "distortionXMin": 10,
    "distortionXMax": 190,
    "distortionYMin": 10,
    "distortionYMax": 190,
    "sdRunOnStop": "",
    "sdStopHeaterMotorsOnStop": "1",
    "featureRetraction": "1",
    "autoretractEnabled": "0",
    "retractionLength": 3,
    "retractionLongLength": 13,
    "retractionSpeed": 40,
    "retractionZLift": 0,
    "retractionUndoExtraLength": 0,
    "retractionUndoExtraLongLength": 0,
    "retractionUndoSpeed": 20,
    "filamentChangeXPos": 0,
    "filamentChangeYPos": 0,
    "filamentChangeZAdd": 2,
    "filamentChangeRehome": 1,
    "filamentChangeShortRetract": 5,
    "filamentChangeLongRetract": 50,
    "fanKickstart": 200,
    "servo0StartPos": -1,
    "servo1StartPos": -1,
    "servo2StartPos": -1,
    "servo3StartPos": -1,
    "uiDynamicEncoderSpeed": "1",
    "uiServoControl": 0,
    "killIfSensorDefect": "0",
    "jamSteps": 220,
    "jamSlowdownSteps": 320,
    "jamSlowdownTo": 70,
    "jamErrorSteps": 500,
    "jamMinSteps": 10,
    "jamAction": 1,
    "primaryPort": 0,
    "numMotorDrivers": 0,
    "motorDrivers": [
        {
            "t": "None",
            "s": "",
            "invertEnable": "0",
            "invertDirection": "0",
            "stepsPerMM": 100,
            "speed": 10,
            "dirPin": -1,
            "stepPin": -1,
            "enablePin": -1
        },
        {
            "t": "None",
            "s": "",
            "invertEnable": "0",
            "invertDirection": "0",
            "stepsPerMM": 100,
            "speed": 10,
            "dirPin": -1,
            "stepPin": -1,
            "enablePin": -1
        },
        {
            "t": "None",
            "s": "",
            "invertEnable": "0",
            "invertDirection": "0",
            "stepsPerMM": 100,
            "speed": 10,
            "dirPin": -1,
            "stepPin": -1,
            "enablePin": -1
        },
        {
            "t": "None",
            "s": "",
            "invertEnable": "0",
            "invertDirection": "0",
            "stepsPerMM": 100,
            "speed": 10,
            "dirPin": -1,
            "stepPin": -1,
            "enablePin": -1
        },
        {
            "t": "None",
            "s": "",
            "invertEnable": "0",
            "invertDirection": "0",
            "stepsPerMM": 100,
            "speed": 10,
            "dirPin": -1,
            "stepPin": -1,
            "enablePin": -1
        },
        {
            "t": "None",
            "s": "",
            "invertEnable": "0",
            "invertDirection": "0",
            "stepsPerMM": 100,
            "speed": 10,
            "dirPin": -1,
            "stepPin": -1,
            "enablePin": -1
        }
    ],
    "manualConfig": "",
    "zHomeMinTemperature": 0,
    "zHomeXPos": 999999,
    "zHomeYPos": 999999,
    "zHomeHeatHeight": 20,
    "zHomeHeatAll": "1",
    "zProbeZOffsetMode": 0,
    "zProbeZOffset": 0,
    "uiBedCoating": "1",
    "langEN": "1",
    "langDE": "0",
    "langNL": "0",
    "langPT": "0",
    "langIT": "0",
    "langES": "0",
    "langFI": "0",
    "langSE": "0",
    "langFR": "0",
    "langCZ": "0",
    "langPL": "0",
    "langTR": "0",
    "interpolateAccelerationWithZ": 0,
    "accelerationFactorTop": 100,
    "bendingCorrectionA": 0,
    "bendingCorrectionB": 0,
    "bendingCorrectionC": 0,
    "preventZDisableOnStepperTimeout": "0",
    "supportLaser": "0",
    "laserPin": -1,
    "laserOnHigh": "1",
    "defaultPrinterMode": 0,
    "supportCNC": "0",
    "cncWaitOnEnable": 300,
    "cncWaitOnDisable": 0,
    "cncEnablePin": -1,
    "cncEnableWith": "1",
    "cncDirectionPin": -1,
    "cncDirectionCW": "1",
    "startupGCode": "",
    "jsonOutput": "0",
    "bedLevelingMethod": 0,
    "bedCorrectionMethod": 0,
    "bedLevelingGridSize": 5,
    "bedLevelingRepetitions": 5,
    "bedMotor1X": 0,
    "bedMotor1Y": 0,
    "bedMotor2X": 200,
    "bedMotor2Y": 0,
    "bedMotor3X": 100,
    "bedMotor3Y": 200,
    "zProbeRequiresHeating": "0",
    "zProbeMinTemperature": 150,
    "adcKeypadPin": -1,
    "sharedExtruderHeater": "0",
    "extruderSwitchXYSpeed": 100,
    "dualXAxis": "0",
    "boardFanSpeed": 255,
    "maxHalfstepInterval": 1999,
    "hasMAX6675": false,
    "hasMAX31855": false,
    "hasGeneric1": false,
    "hasGeneric2": false,
    "hasGeneric3": false,
    "hasUser0": false,
    "hasUser1": false,
    "hasUser2": false,
    "numExtruder": 1,
    "version": 92.9,
    "primaryPortName": ""
  }
  ========== End configuration string ==========

*/

↧

layers not aligned. I make a small rectangle and the sides are at 45 degrees.

April 27, 2020, 6:52 pm
$
0
0
Dear Sir: 
Printer worked fine yesterday and I was making those Montana Masks for friends. Today when I print the layers are not aligned. I tried printing a rectangle (60mm length, 20mm width, and 20 mm height) and the ends are at 45 degrees. The ends should be 90 degrees. You can see the print head is moving one layer at a time to the left along the length of the rectangle.. The belts are tight. This has to be a setting someplace. I am using Repitier host is V2.1.6. Printer is a TronXY 3sx with Marlin v2.05 I think. Any ideas? Oh, the board is a Melzi V2.05. Also, the ends are too well printed to be a random print problem. I am using Slice3r which worked great yesterday. I also tried Cura and that did not work either. Could be be a virus? Never heard of such a thing, but who knows. 

 Thanks for all the help. Hope you all are well and stay well. Richard Brown
↧
↧

Fehler in jedem Druck

April 27, 2020, 12:40 pm
$
0
0
Hallo Freunde!

Ich nutze Repetier Server seit ca. 4 Wochen und habe bis dato keinerlei Probleme gehabt. Ich nutze das ganze mit dem aktuellen Raspberry Pi mit 2GB RAM. Seit 2 Tagen kämpfe ich mit dem Artillery Sidewinder X1 und Repetier Server mit extremen Problemen. Kein Druck gelingt, mitten im Druck, egal ob nach 3mm, oder 1cm, oder 2cm, 5cm...er macht wahllos an irgend einer Stelle dann eine Unterextrusion, das mehrere Schichten, danach funktioniert er wieder problemlos. Gestern Nacht einen 3h Druck laufen lassen, heute morgen Spaghetti wohin man schaut. Das gleiche wieder. Das Objekt habe ich nun schon 5x neu gesliced, jedes mal das gleiche, aber die Unterextrusion beginnt wahllos an irgend einem Punkt, egal wo. Das entscheidet immer der Zufall. Von Samstag zu Sonntag habe ich ein großes 9h Projekt gedruckt, hier ging das Problem nach ca. 7h los, dort hab ich massive Layershifts gehabt und auch teils Unterextrusion. Von MicroSD druckt mein Drucker jedes Objekt einwandfrei. Ich bekomme seitdem keinen einzigen Druck mehr einwandfrei hin. Jeder Druck kommt so raus wie der vorherige.

Ist das Problem bekannt?


Viele Grüße,
Clemens.
↧

STM32 Firmware Flash

December 19, 2019, 2:10 am
$
0
0
Hi,
I use rumba32 with repertier server and as mk4duo and klipper firmware (in test). I was wondering if there is a way to program the card directly from the repetier server. I for mk4duo generate a .hex file from the arduino compiler 1.8.10. Thank you very much for helping. Lorenzo
↧
Search

Repetier Server with Hyperpixel 4 touchscreen?

April 3, 2019, 11:30 am
$
0
0
Has anyone had any luck using the Pimoroni Hyperpixel 4 with Repetier Server?  The Hyperpixel install script works just fine on a standard Raspbian install, but for some reason when I run it on the Repetier Server Raspberry Pi image, the display refuses to work, despite the install script completing without error.  There's something in the Repetier Server image that disagrees with the Hyperpixel, but I have no idea what.  Any ideas?
↧

crash detection, power panic, and runout filament sensor Prusa mk3s

April 28, 2020, 5:07 am
$
0
0
Hi. 
Does the prusa detect these things when connected to repetier server? crash detection, power panic, and runout filament sensor 
↧
↧

Re-scales drawing when going from inventor to Repetier

April 28, 2020, 7:21 am
$
0
0
When I take a drawing that has been done on Inventor in mm to Repetier it is not the same size. Repetier is also set to mm.

How can I fix this?

Thanks
↧

Change colorscheme on raspberrry touchscreen

March 24, 2020, 5:02 am
$
0
0
is it possible to change this yellowish (i think #d39e3b) colour accents on the touch menu?
i found a css with many of these colorcodes at 
/usr/local/Repetier-Server/www/modules/front2/www/css/
How is the address to access this page from a pc browser to inspect all elements?

Would be nice if you can implement a variable wich can be loaded from the settings. Or just a dropdown for different themes

Gute Arbeit! Freue mich auf die nächsten Updates!

↧

Probleme mit der Aktivierung, Error 400

April 28, 2020, 10:25 am
$
0
0
Hallo, ich habe gerade mein RASPI mit 7'' Display server neu aufgesetzt (korruptes File-System).

leider bekomme ich jetzt beim eingeben des Lizensschlüssels folgende Meldung:

 "Error communicationg with License server:400" … usw...

Der Raspi hat Zugang zum Internet z.B. ping www.apple.com ist alles ok
 
aber bei:
wget https://licence.internetloesungen.com/

bekomme ich:
--2019-12-11 12:06:29--  https://licence.internetloesungen.com/
Resolving licence.internetloesungen.com (licence.internetloesungen.com)... 94.130.164.39
Connecting to licence.internetloesungen.com (licence.internetloesungen.com)|94.130.164.39|:443... connected.
ERROR: The certificate of ‘licence.internetloesungen.com’ is not trusted.
ERROR: The certificate of ‘licence.internetloesungen.com’ is not yet activated.
The certificate has not yet been activated

Ist das jetzt ein Problem auf meinem Ende oder bei dem Lizens-Server?
↧
Viewing all 9285 articles
Browse latest View live
Search

Latest Images

Crisis-hit NHS fat cats raking in MASSIVE salaries as frontline services cry...

Crisis-hit NHS fat cats raking in MASSIVE salaries as frontline services cry...

July 19, 2025, 2:11 pm
NBC Sports’ Super Bowl commercial cost revealed after Fox made $800 million...

NBC Sports’ Super Bowl commercial cost revealed after Fox made $800 million...

July 19, 2025, 2:04 pm
Lewis Capaldi locked in planning battle with neighbour at £1.6M pad weeks...

Lewis Capaldi locked in planning battle with neighbour at £1.6M pad weeks...

July 19, 2025, 1:35 pm
Beloved I’m A Celeb winner and TV star who lasted just THREE DAYS on brink of...

Beloved I’m A Celeb winner and TV star who lasted just THREE DAYS on brink of...

July 19, 2025, 1:06 pm
WATCH: What you need to know about the Pacquiao-Barrios title fight

WATCH: What you need to know about the Pacquiao-Barrios title fight

July 19, 2025, 6:46 am
Review: Skil PWRCore 20 18-Gauge Brad Nailer

Review: Skil PWRCore 20 18-Gauge Brad Nailer

July 19, 2025, 5:00 am
Why Not Try Sanity?

Why Not Try Sanity?

July 19, 2025, 4:17 am
Inside sick ‘child fight clubs’ where gangs lure teens into savage street...

Inside sick ‘child fight clubs’ where gangs lure teens into savage street...

July 19, 2025, 3:59 am
Met Eireann’s 24-hour weather alert kicks in with ‘heavy rain’ and ‘isolated...

Met Eireann’s 24-hour weather alert kicks in with ‘heavy rain’ and ‘isolated...

July 19, 2025, 3:00 am
Manny Pacquiao vs Mario Barrios undercard thrown into chaos as fighter is...

Manny Pacquiao vs Mario Barrios undercard thrown into chaos as fighter is...

July 19, 2025, 2:52 am